- 您現在的位置：買賣IC網 > PDF目錄371440 > 29LV160C-55R (Macronix International Co., Ltd.) 16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29LV160C-55R |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 中文描述： | 1,600位[2Mx8/1Mx16] CMOS單電壓3V時僅閃存 |
| 文件頁數： | 16/66頁 |
| 文件大小： | 778K |
| 代理商： | 29LV160C-55R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
16
P/N:PM1186
MX29LV160C T/B
REV. 1.2, JAN. 19, 2006
device then returns to reading array data and addresses
are no longer latched. The system can determine the
status of the program operation by using
Q7, Q6, or RY/BY#. See "Write Operation Status" for
information on these status bits.
Any commands written to the device during the Embed-
ded Program Algorithm are ignored. Note that a hardware
reset immediately terminates the programming
operation. The Byte/Word Program command sequence
should be reinitiated once the device has reset to read-
ing array data, to ensure data integrity.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed from a
"0" back to a "1". Attempting to do so may cause the
device to set Q5 to "1", or cause the Data# Polling algo-
rithm to indicate the operation was successful. However,
a succeeding read will show that the data is still "0".
Only erase operations can convert a "0" to a "1".
WRITE OPERATION STATUS
The device provides several bits to determine the status
of a write operation: Q2, Q3, Q5, Q6, Q7, and RY/BY#.
Table 8 and the following subsections describe the func-
tions of these bits. Q7, RY/BY#, and Q6 each offer a
method for determining whether a program or erase op-
eration is complete or in progress. These three bits are
discussed first.
Q7: Data# Polling
The Data# Polling bit, Q7, indicates to the host system
whether an Automatic Algorithm is in progress or com-
pleted, or whether the device is in Erase Suspend. Data#
Polling is valid after the rising edge of the final WE# pulse
in the program or erase command sequence.
During the Automatic Program algorithm, the device out-
puts on Q7 the complement of the datum programmed to
Q7. This Q7 status also applies to programming during
Erase Suspend. When the Automatic Program algorithm
is complete, the device outputs the datum programmed
to Q7. The system must provide the program address to
read valid status information on Q7. If a program address
falls within a protected sector, Data# Polling on Q7 is
active for approximately 1 us, then the device returns to
reading array data.
During the Automatic Erase algorithm, Data# Polling pro-
duces a "0" on Q7. When the Automatic Erase algorithm
is complete, or if the device enters the Erase Suspend
mode, Data# Polling produces a "1" on Q7. This is analo-
gous to the complement/true datum output described for
the Automatic Program algorithm: the erase function
changes all the bits in a sector to "1" prior to this, the
device outputs the "complement,
”
or "0".
”
The system
must provide an address within any of the sectors se-
lected for erasure to read valid status information on Q7.
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Data# Polling on
Q7 is active for approximately 100 us, then the device
returns to reading array data. If not all selected sectors
are protected, the Automatic Erase algorithm erases the
unprotected sectors, and ignores the selected sectors
that are protected.
When the system detects Q7 has changed from the
complement to true data, it can read valid data at Q7-Q0
on the following read cycles. This is because Q7 may
change asynchronously with Q0-Q6 while Output Enable
(OE#) is asserted low.
RY/BY# : Ready/Busy
The RY/BY# is a dedicated, open-drain output pin that
indicates whether an Automatic Erase/Program algorithm
is in progress or complete. The RY/BY# status is valid
after the rising edge of the final WE# or CE#, whichever
happens first, in the command sequence. Since RY/BY#
is an open-drain output, several RY/BY# pins can be tied
together in parallel with a pull-up resistor to Vcc.
If the output is low (Busy), the device is actively erasing
or programming. (This includes programming in the Erase
Suspend mode.) If the output is high (Ready), the device
is ready to read array data (including during the Erase
Suspend mode), or is in the standby mode.
Table 8 shows the outputs for RY/BY# during write op-
eration.
Q6:Toggle BIT I
Toggle Bit I on Q6 indicates whether an Automatic Pro-
gram or Erase algorithm is in progress or complete, or
whether the device has entered the Erase Suspend mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 29LV160C-70 | 16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV160C-90 | 16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV320BTC-70 | 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-55R | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-70 | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29LV160C-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV160C-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV160DB70EC | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 29LV160DB-70EC | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 29LV160DB70EI | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。