- 您現在的位置：買賣IC網 > PDF目錄371440 > 29SL800CB-90 (Macronix International Co., Ltd.) 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29SL800CB-90 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 中文描述： | 800萬位[1Mx8/512K x16] CMOS單電壓僅1.8V的閃存 |
| 文件頁數： | 14/64頁 |
| 文件大?。?/td> | 750K |
| 代理商： | 29SL800CB-90 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
14
P/N:PM1224
MX29SL800C T/B
REV. 1.0, APR. 20, 2006
time of tREADY (not during Embedded Algorithms). The
system can read data tRH after the RESET# pin returns
to VIH.
Refer to the AC Characteristics tables for RESET#
parameters and to Figure 22 for the timing diagram.
READ/RESET COMMAND
The read or reset operation is initiated by writing the read/
reset command sequence into the command register.
Microprocessor read cycles retrieve array data. The de-
vice remains enabled for reads until the command regis-
ter contents are altered.
If program-fail or erase-fail happen, the write of F0H will
reset the device to abort the operation. A valid com-
mand must then be written to place the device in the
desired state.
SILICON-ID READ COMMAND
Flash memories are intended for use in applications where
the local CPU alters memory contents. As such, manu-
facturer and device codes must be accessible while the
device resides in the target system. PROM program-
mers typically access signature codes by raising A9 to
a high voltage (VID). However, multiplexing high voltage
onto address lines is not generally desired system de-
sign practice.
The MX29SL800C T/B contains a Silicon-ID-Read op-
eration to supple traditional PROM programming meth-
odology. The operation is initiated by writing the read
silicon ID command sequence into the command regis-
ter. Following the command write, a read cycle with
A1=VIL, A0=VIL retrieves the manufacturer code of C2H/
00C2H. A read cycle with A1=VIL, A0=VIH returns the
device code of EAH/22EAH for MX29SL800CT, 6BH/
226BH for MX29SL800CB.
SET-UP AUTOMATIC CHIP/SECTOR ERASE
COMMANDS
Chip erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
"set-up" command 80H. Two more "unlock" write cycles
are then followed by the chip erase command 10H or
sector erase command 30H.
The Automatic Chip Erase does not require the device to
be entirely pre-programmed prior to executing the Auto-
matic Chip Erase. Upon executing the Automatic Chip
Erase, the device will automatically program and verify
the entire memory for an all-zero data pattern. When the
device is automatically verified to contain an all-zero pat-
tern, a self-timed chip erase and verify begin. The erase
and verify operations are completed when the data on Q7
is "1" at which time the device returns to the Read mode.
The system is not required to provide any control or tim-
ing during these operations.
When using the Automatic Chip Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array
(no erase verification command is required).
If the Erase operation was unsuccessful, the data on Q5
is "1" (see Table 8), indicating the erase operation ex-
ceed internal timing limit.
The automatic erase begins on the rising edge of the last
WE# or CE# pulse, whichever happens first in the com-
mand sequence and terminates when the data on Q7 is
"1" at which time the device returns to the Read mode,
or the data on Q6 stops toggling for two consecutive read
cycles at which time the device returns to the Read mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 29SL800CT-90 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29U194A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U194ADFE | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U194AFS | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U294A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29SL800CT-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 29SM-K035-00V | 功能描述:MOTOR STEP UNI 71MM DIA 24V RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
| 29SM-K035-99V | 功能描述:MOTOR STEP UNI 71MM 24V DL SHFT RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
| 29SM-K138-00V | 功能描述:MOTOR STEP UNI 71MM DIA 24V RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
| 29SM-K138-99V | 功能描述:MOTOR STEP UNI 71MM 24V DL SHFT RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
發布緊急采購，3分鐘左右您將得到回復。