- 您現在的位置：買賣IC網 > PDF目錄371440 > 29SL800CT-90 (Macronix International Co., Ltd.) 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29SL800CT-90 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY |
| 中文描述： | 800萬位[1Mx8/512K x16] CMOS單電壓僅1.8V的閃存 |
| 文件頁數： | 18/64頁 |
| 文件大?。?/td> | 750K |
| 代理商： | 29SL800CT-90 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
18
P/N:PM1224
MX29SL800C T/B
REV. 1.0, APR. 20, 2006
During an Automatic Program or Erase algorithm opera-
tion, successive read cycles to any address cause Q6
to toggle. The system may use either OE# or CE# to
control the read cycles. When the operation is complete,
Q6 stops toggling.
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Q6 toggles and
returns to reading array data. If not all selected sectors
are protected, the Automatic Erase algorithm erases the
unprotected sectors, and ignores the selected sectors
that are protected.
The system can use Q6 and Q2 together to determine
whether a sector is actively erasing or is erase sus-
pended. When the device is actively erasing (that is, the
Automatic Erase algorithm is in progress), Q6 toggling.
When the device enters the Erase Suspend mode, Q6
stops toggling. However, the system must also use Q2
to determine which sectors are erasing or erase-sus-
pended. Alternatively, the system can use Q7.
If a program address falls within a protected sector, Q6
toggles for approximately 2 us after the program com-
mand sequence is written, then returns to reading array
data.
Q6 also toggles during the erase-suspend-program mode,
and stops toggling once the Automatic Program algo-
rithm is complete.
Table 8 shows the outputs for Toggle Bit I on Q6.
Q2:Toggle Bit II
The "Toggle Bit II" on Q2, when used with Q6, indicates
whether a particular sector is actively erasing (that is,
the Automatic Erase algorithm is in process), or whether
that sector is erase-suspended. Toggle Bit II is valid
after the rising edge of the final WE# or CE#, whichever
happens first, in the command sequence.
Q2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
system may use either OE# or CE# to control the read
cycles.) But Q2 cannot distinguish whether the sector
is actively erasing or is erase-suspended. Q6, by com-
parison, indicates whether the device is actively eras-
ing, or is in Erase Suspend, but cannot distinguish which
sectors are selected for erasure. Thus, both status bits
are required for sectors and mode information. Refer to
Table 8 to compare outputs for Q2 and Q6.
Reading Toggle Bits Q6/ Q2
Whenever the system initially begins reading toggle bit
status, it must read Q7-Q0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the
system would note and store the value of the toggle bit
after the first read. After the second read, the system
would compare the new value of the toggle bit with the
first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system
can read array data on Q7-Q0 on the following read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the sys-
tem also should note whether the value of Q5 is high
(see the section on Q5). If it is, the system should then
determine again whether the toggle bit is toggling, since
the toggle bit may have stopped toggling just as Q5 went
high. If the toggle bit is no longer toggling, the device
has successfully completed the program or erase op-
eration. If it is still toggling, the device did not complete
the operation successfully, and the system must write
the reset command to return to reading array data.
The remaining scenario is that system initially determines
that the toggle bit is toggling and Q5 has not gone high.
The system may continue to monitor the toggle bit and
Q5 through successive read cycles, determining the sta-
tus as described in the previous paragraph. Alterna-
tively, it may choose to perform other system tasks. In
this case, the system must start at the beginning of the
algorithm when it returns to determine the status of the
operation.
Q5
Exceeded Timing Limits
Q5 will indicate if the program or erase time has ex-
ceeded the specified limits (internal pulse count). Under
these conditions Q5 will produce a "1". This time-out
condition indicates that the program or erase cycle was
not successfully completed. Data# Polling and Toggle
Bit are the only operating functions of the device under
this condition.
happens first, in the command sequence (prior to the
program or erase operation), and during the sector time-
out.
相關PDF資料 |
PDF描述 |
|---|---|
| 29U194A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U194ADFE | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U194AFS | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U294A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29U294ADFE | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29SM-K035-00V | 功能描述:MOTOR STEP UNI 71MM DIA 24V RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
| 29SM-K035-99V | 功能描述:MOTOR STEP UNI 71MM 24V DL SHFT RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
| 29SM-K138-00V | 功能描述:MOTOR STEP UNI 71MM DIA 24V RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
| 29SM-K138-99V | 功能描述:MOTOR STEP UNI 71MM 24V DL SHFT RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
| 29SM-K250-00V | 功能描述:MOTOR STEP UNI 71MM DIA 24V RoHS:是 類別:電機，螺線管 >> 步進電機 系列:29SM 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
發布緊急采購，3分鐘左右您將得到回復。