- 您現在的位置：買賣IC網 > PDF目錄247552 > 2DC79PF173 (ITT CANNON) 79 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, CRIMP PDF資料下載
參數資料
| 型號： | 2DC79PF173 |
| 廠商： | ITT CANNON |
| 元件分類： | D-微型連接器 |
| 英文描述： | 79 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 文件頁數： | 2/10頁 |
| 文件大?。?/td> | 607K |
| 代理商： | 2DC79PF173 |
69
www.ittcannon.com
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
The Centi Line - .075" Contact Spacing
2D/CTA
CTA Assembly Instructions
.275 (6.98)
MAX.
.475 (12.06)
MAX.
INSERTION
Guide Posts
Polarizing Posts
1. Place the connector into the slot in the assembly block
with the arrows on the insulator pointing downward. The
connector will bottom against the internal shoulder in the
groove in the assembly block. Start contact insertion by
placing the crimped contact in the cavity by hard.
3. With firm steady pressure, push the contact into the
cavity until the resilient internal shoulder snaps into the
locking groove in the contact. To prevent over insertion,
the tool tip bottoms against the rear of the insulator.
4. The guide post and polarizing posts are inserted in teh
same manner as the contacts. The guide posts are inserted
into the socket insulator, and the polarizing posts are
inserted into the pin insulartor. The corresponding contact
in the mating insulator must be removed for each.
2. Position the insertion tool tip on the rear of contact as
shown. The insulation must be pulled back from the crimp
pot approximately 1/32" to allow the tool tip to butt
against the contact crimp pot.
EXTRACTION
1. To extract the contacts, place the conector face up in
the assembly block so that the contact to be extracted is
in the end of the block that has a fully slotted opening.
2. The pin extraction tool tip is tubular, slides over the pin
bundle and butts against the front shoulder of the pin. The
socket extraction tool is a solid rod that fits into the socket
contact, the external shoulder butts against the contact
socket shoulder.
3. Insert the extraction tool into the cavity and apply firm
pressure until the contact is pushed thru the rear of the
connector.
4. Lift the insulator from the groove and pull the contact
out. Repeat for balance of contacts to be removed.
相關PDF資料 |
PDF描述 |
|---|---|
| 240-382AMT24-24SPCFNU | 24 CONTACT(S), ALUMINUM ALLOY, NICKEL PLATED, FEMALE-MALE, CIRCULAR ADAPTER |
| 240-382AZN20-25SPPENU | 25 CONTACT(S), ALUMINUM ALLOY, ZINC NICKEL PLATED, FEMALE-MALE, CIRCULAR ADAPTER |
| 240-382AZN20-25SPPFNU | 25 CONTACT(S), ALUMINUM ALLOY, ZINC NICKEL PLATED, FEMALE-MALE, CIRCULAR ADAPTER |
| 240-382AZN20-25SPPGNU | 25 CONTACT(S), ALUMINUM ALLOY, ZINC NICKEL PLATED, FEMALE-MALE, CIRCULAR ADAPTER |
| 240-382AZN20-25SPPXNU | 25 CONTACT(S), ALUMINUM ALLOY, ZINC NICKEL PLATED, FEMALE-MALE, CIRCULAR ADAPTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 2DC-79PF173 | 功能描述:79 位 D-Sub，雙密度 插頭，公引腳 連接器, 自由懸掛 壓接 制造商:itt cannon, llc 系列:微型，2D 包裝:散裝 零件狀態:要求報價 連接器樣式:D-Sub，雙密度 連接器類型:插頭，公引腳 針腳數:79 排數:3 外殼尺寸，連接器布局:4（DC，C）雙密度 觸頭類型:信號 安裝類型:自由懸掛 法蘭特性:電纜側，公頭頂絲（4-40） 端接:壓接 特性:- 外殼材料，鍍層:鋼，黃色鍍鉻鎘 觸頭鍍層:金 觸頭鍍層厚度:- 侵入防護:- 工作溫度:-55°C ~ 85°C 額定電壓:- 額定電流:5A 外殼材料:聚酰胺（PA），尼龍，玻璃纖維增強型 顏色:黑 標準包裝:1 |
| 2DC79P-F173 | 制造商:ITT Interconnect Solutions 功能描述:2DC79P-F173 - Bulk 制造商:ITT Interconnect Solutions 功能描述:Conn High Density D-Sub PIN 79 POS Crimp ST Panel Mount 79 Terminal 1 Port |
| 2DC-79PF173F0 | 制造商:ITT 功能描述:2DC-79PF173F0 制造商:ITT Interconnect Solutions 功能描述:2DC-79PF173F0 |
| 2DC79P-F173-F0 | 制造商:ITT Interconnect Solutions 功能描述:Conn High Density D-Sub PIN 79 POS Crimp ST Panel Mount 79 Terminal 1 Port |
| 2DC79P-F173-FO | 制造商:ITT Interconnect Solutions 功能描述:2DC79P-F173-FO - Bulk |
發布緊急采購，3分鐘左右您將得到回復。