- 您現在的位置：買賣IC網 > PDF目錄156551 > 37C67X (SMSC Corporation) ENHANCED SUPER I/O CONTROLLER WITH FAST IR PDF資料下載
參數資料
| 型號： | 37C67X |
| 廠商： | SMSC Corporation |
| 英文描述： | ENHANCED SUPER I/O CONTROLLER WITH FAST IR |
| 中文描述： | 增強的超級I / O控制器，快速紅外線 |
| 文件頁數： | 183/194頁 |
| 文件大?。?/td> | 546K |
| 代理商： | 37C67X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁當前第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁
89
Software Constraints
Before an EPP cycle is executed, the software
must ensure that the control register bit PCD is
a logic "0" (ie a 04H or 05H should be written to
the Control port). If the user leaves PCD as a
logic "1", and attempts to perform an EPP write,
the chip is unable to perform the write (because
PCD is a logic "1") and will appear to perform an
EPP read on the parallel bus, no error is
indicated.
EPP 1.9 Write
The timing for a write operation (address or
data) is shown in timing diagram EPP Write
Data or Address cycle.
IOCHRDY is driven
active low at the start of each EPP write and is
released when it has been determined that the
write cycle can complete.
The write cycle can
complete under the following circumstances:
1.
If the EPP bus is not ready (nWAIT is active
low) when nDATASTB or nADDRSTB goes
active then the write can complete when
nWAIT goes inactive high.
2.
If the EPP bus is ready (nWAIT is inactive
high) then the chip must wait for it to go
active low before changing the state of
nDATASTB, nWRITE or nADDRSTB. The
write
can
complete
once
nWAIT
is
determined inactive.
Write Sequence of operation
1.
The host selects an EPP register, places
data on the SData bus and drives nIOW
active.
2.
The chip drives IOCHRDY inactive (low).
3.
If WAIT is not asserted, the chip must wait
until WAIT is asserted.
4.
The chip places address or data on PData
bus, clears PDIR, and asserts nWRITE.
5.
Chip asserts nDATASTB or nADDRSTRB
indicating that PData bus contains valid
information, and the WRITE signal is valid.
6.
Peripheral deasserts nWAIT, indicating that
any setup requirements have been satisfied
and the chip may begin the termination
phase of the cycle.
7.
a)
The
chip
deasserts
nDATASTB
or
nADDRSTRB, this marks the beginning
of the termination phase. If it has not
already done so, the peripheral should
latch the information byte now.
b)
The chip latches the data from the
SData bus for the PData bus and
asserts (releases) IOCHRDY allowing
the host to complete the write cycle.
8.
Peripheral asserts nWAIT, indicating to the
host that any hold time requirements have
been
satisfied
and
acknowledging
the
termination of the cycle.
9.
Chip may modify nWRITE and nPDATA in
preparation for the next cycle.
EPP 1.9 Read
The timing for a read operation (data) is shown
in timing diagram EPP Read Data cycle.
IOCHRDY is driven active low at the start of
each EPP read and is released when it has been
determined that the read cycle can complete.
The read cycle can complete under the following
circumstances:
1
If the EPP bus is not ready (nWAIT is active
low) when nDATASTB goes active then the
read can complete when nWAIT goes
inactive high.
2.
If the EPP bus is ready (nWAIT is inactive
high) then the chip must wait for it to go
active low before changing the state of
WRITE or before nDATASTB goes active.
The read can complete once nWAIT is
determined inactive.
相關PDF資料 |
PDF描述 |
|---|---|
| 37C957FR | ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS |
| 37FMA1-ABW31N | SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED |
| 37FML1-BEW31N | SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED |
| 37FML2-ACW21N | SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 1A, 24VDC, PANEL MOUNT-THREADED |
| 37FMA1-AAW11N | SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 37C-6BH-5-5 | 制造商:Birtcher Products 功能描述: |
| 37C72U-185 | 制造商:White-Rodgers 功能描述: |
| 37C73U-170 | 制造商:White-Rodgers 功能描述: |
| 37C73U-171 | 制造商:White-Rodgers 功能描述: |
| 37C922BQFP | 制造商:SMSC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。