參數資料
型號： 37M602
廠商： SMSC Corporation
英文描述： ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
中文描述： 增強的超級I / O控制器，支持紅外線
文件頁數： 140/182頁
文件大小： 650K
代理商： 37M602
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁當前第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁
60
this manner, parallel seek operations may be
done on up to four drives at once.
Note that if implied seek is not enabled, the read
and write commands should be preceded by:
1) Seek command - Step to the proper track
2) Sense
Interrupt
Status
command
-
Terminate the Seek command
3) Read ID - Verify head is on proper track
4) Issue Read/Write command.
The Seek command does not have a result
phase. Therefore, it is highly recommended that
the Sense Interrupt Status command be issued
after the Seek command to terminate it and to
provide verification of the head position (PCN).
The H bit (Head Address) in ST0 will always
return to a "0".
When exiting POWERDOWN
mode, the FDC clears the PCN value and the
status information to zero. Prior to issuing the
POWERDOWN
command,
it
is
highly
recommended that the user service all pending
interrupts through the Sense Interrupt Status
command.
Sense Interrupt Status
An interrupt signal on FINT pin is generated by
the FDC for one of the following reasons:
1. Upon entering the Result Phase of:
a. Read Data command
b. Read A Track command
c. Read ID command
d. Read Deleted Data command
e. Write Data command
f.
Format A Track command
g. Write Deleted Data command
h. Verify command
2. End of Seek, Relative Seek, or Recalibrate
command
3. FDC requires a data transfer during the
execution phase in the non-DMA mode
The Sense Interrupt Status command resets the
interrupt signal and, via the IC code and SE bit
of Status Register 0, identifies the cause of the
interrupt.
Table 28 - Interrupt Identification
The Seek, Relative Seek, and Recalibrate
commands have no result phase.
The Sense
Interrupt Status command must be issued
immediately after these commands to terminate
them and to provide verification of the head
position (PCN).
The H (Head Address) bit in
ST0 will always return a "0". If a Sense Interrupt
Status is not issued, the drive will continue to be
BUSY and may affect the operation of the next
command.
Sense Drive Status
Sense
Drive
Status
obtains
drive
status
information.
It has not execution phase and
goes directly to the result phase from the
command phase.
Status Register 3 contains
the drive status information.
Specify
The Specify command sets the initial values for
each of the three internal times.
The HUT
(Head Unload Time) defines the time from the
end of the execution phase of one of the
read/write commands to the head unload state.
The SRT (Step Rate Time) defines the time
interval between adjacent step pulses. Note that
the spacing between the first and second step
pulses may be shorter than the remaining step
SE
IC
INTERRUPT DUE TO
0
1
11
00
01
Polling
Normal termination of Seek
or Recalibrate command
Abnormal termination of
Seek or Recalibrate
command
相關PDF資料
PDF描述
38-00-5829 9 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER
38-00-5830 10 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER
38-00-5831 11 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER
38-00-5832 12 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER
38-00-5833 13 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER
相關代理商/技術參數
參數描述
37MM140HR1240K 制造商:Eaton Corporation 功能描述:400A Commercial Meter Stack, 3PH, 7 Jaw Bolt On Socket, K Ba
37MM140R1240K 制造商:Eaton Corporation 功能描述:400A Commercial Meter Stack, 3PH, 7 Jaw Bolt On Socket, K Ba
37MM420R12 制造商:Eaton Corporation 功能描述:3 PHASE, 7 JAW COMM METERING MODULE, 4 SOCKETS, 200A
37MTXT4BHF 制造商:Siemens 功能描述:
37N 制造商:APEX TOOL GROUP 功能描述:7 1/8 IN. FORGED STEEL, NICKEL PLATED, INDUSTRIAL STRAIGHT TRIMMER, INLAID 制造商:APEX TOOL GROUP 功能描述:7 1/8 IN. FORGED STEEL, NICKEL PLATED, INDUSTRIAL STRAIGHT TRIMMER, INLAID, Wiss
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*