- 您現在的位置：買賣IC網 > PDF目錄33563 > 400WA10M12.5X16 (ON SEMICONDUCTOR) Low-Cost 100 mA High-Voltage Buck and Buck-Boost Using NCP1052 PDF資料下載
參數資料
| 型號： | 400WA10M12.5X16 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Low-Cost 100 mA High-Voltage Buck and Buck-Boost Using NCP1052 |
| 中文描述： | 低成本百毫安高電壓降壓和降壓升壓使用NCP1052 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 93K |
| 代理商： | 400WA10M12.5X16 |
AND8098/D
http://onsemi.com
6
The proposed buck-boost is better in term of the standby
ability. It is because the VCC charging current in Figure 2(b)
only passes through the inductor. The charging current
pulses become an averaged energy stored in the inductor and
consume smaller amount of power comparing to the buck
case.
Figure 7. Auxiliary Winding to improve standby
Abillity
(a) Buck
(b) Buck-boost
The auxiliary winding to supply the VCC voltage in Figure
7 is a method to improve the standby ability. The auxiliary
winding keeps the VCC voltage above 7.5 V and disable the
VCC charging current and hence its standby loss. The
auxiliary winding is coupled from the inductor L with
polarity same as the regulated output voltage. The VCC
voltage in the auxiliary winding is designed to be between
the normal VCC limits of 7.5 and 8.5 V typically. The
frequency jittering feature loses when the VCC voltage is
fixed. When output is shorted, there will be no voltage
coming from the auxiliary winding and the circuit will enter
fault mode with the 4.5 V-8.5 V-7.5 V-4.5 V hysteresis
loop.
Another method to supply the VCC voltage is coupling
capacitor technique in Figure 8. The output voltage is
coupled to the inserted capacitor when the diodes are closed.
The voltage drop of the diodes compensate each other.
Hence, the diode voltage drop effect can be neglected. The
NCP1052 needs a nominal VCC voltage of 8V. The inserted
resistor consumes some voltage from the output voltage Vout
to make a 8V to the VCC pin. Based on the 0.5mA typical
current consumption of VCC pin. The inserted resistance
value is (Vout - 8) / 0.5 k
W.
Figure 8. Coupling Capacitor Technique to
Improve Standby Abillity
(a) Buck
(b) Buck-boost
Temperature Rise
The NCP1052 is a very compact package with the control
circuit and high-voltage power switch. Its typical on
resistance is 22
. Temperature rise exists. It is
recommended to design the PCB board with a large copper
area next to the device as a heatsink. This heatsink decreases
相關PDF資料 |
PDF描述 |
|---|---|
| 400WA68M18X25 | MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS |
| 400WXA10M125X16 | MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS |
| 400WXA10M16X16 | MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS |
| 400WXA22M16X20 | MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS |
| 400WXA22M18X16 | MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 400WA10M16X16 | 制造商:RUBYCON 制造商全稱:RUBYCON CORPORATION 功能描述:MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS |
| 400WA10MEFC12.5X16 | 功能描述:CAP ALUM 10UF 400V 20% RADIAL RoHS:是 類別:電容器 >> 鋁 系列:* 標準包裝:2,000 系列:142 RHS 電容:4700µF 額定電壓:10V 容差:±20% 壽命@溫度:105°C 時為 2000 小時 工作溫度:-40°C ~ 105°C 特點:通用 紋波電流:1.26A ESR（等效串聯電阻）:- 阻抗:- 安裝類型:通孔 封裝/外殼:徑向，Can 尺寸/尺寸:0.492" 直徑（12.50mm） 高度 - 座高（最大）:1.063"（27.00mm） 引線間隔:0.197"（5.00mm） 表面貼裝占地面積:- 包裝:散裝 |
| 400WA10MEFCG412.5X16 | 功能描述:CAP ALUM 10UF 400V 20% RADIAL RoHS:是 類別:電容器 >> 鋁 系列:* 標準包裝:2,000 系列:142 RHS 電容:4700µF 額定電壓:10V 容差:±20% 壽命@溫度:105°C 時為 2000 小時 工作溫度:-40°C ~ 105°C 特點:通用 紋波電流:1.26A ESR（等效串聯電阻）:- 阻抗:- 安裝類型:通孔 封裝/外殼:徑向，Can 尺寸/尺寸:0.492" 直徑（12.50mm） 高度 - 座高（最大）:1.063"（27.00mm） 引線間隔:0.197"（5.00mm） 表面貼裝占地面積:- 包裝:散裝 |
| 400WA22M18X16 | 制造商:RUBYCON 制造商全稱:RUBYCON CORPORATION 功能描述:MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS |
| 400WA22M8X9 | 制造商:RUBYCON 制造商全稱:RUBYCON CORPORATION 功能描述:MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS |
發布緊急采購，3分鐘左右您將得到回復。