MAX4066/MAX4066A
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—Single +12V Supply
(V+ = 12V ±10%, GND = 0V, VINH = 4.0V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(Voltages referenced to GND)
V+ ...........................................................................-0.3V to +17V
VIN_, VCOM_, VNO (Note 1) ...........................-0.3V to (V + +0.3V)
Current (any terminal) .........................................................30mA
Peak Current (any terminal) ..............................................100mA
ESD per Method 3015.7 ..................................................>2000V
Continuous Power Dissipation (TA = +70°C)
Plastic DIP (derate 10.00mW/°C above +70°C) ............800mW
Narrow SO (derate 8.00mW/°C above +70°C) ..............640mW
QSOP (derate 9.52mW/°C above +70°C) ......................762mW
CERDIP (derate 9.09mW/°C above +70°C) ....................727mW
Operating Temperature Ranges
MAX4066C_ _/MAX4066AC_ _ .............................0°C to +70°C
MAX4066E_ _/MAX4066AE_ _...........................-40°C to +85°C
MAX4066MJD/MAX4066AMJD .......................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
(Note 3)
V+ = 12V,
VCOM = 0V,
VNO = 10V
V+ = 12V,
ICOM = 2mA,
VNO = 10V
V+ = 12V,
ICOM = 2mA,
VNO = 10V, 5V, 1V
CONDITIONS
nA
-100
100
INO(OFF)
NO or NC Off Leakage
Current (Note 6)
-6
6
-0.1
0.1
-1
1
6
RFLAT(ON)
On-Resistance Flatness
(Note 5)
V
0V+
VCOM,
VNO
Analog Signal Range
24
6
RON
On-Resistance Match
Between Channels (Note 4)
0.5
2
0.5
4
16
45
UNITS
MIN
TYP
MAX
(Note 2)
SYMBOL
PARAMETER
TA = +25°C
MAX4066
MAX4066A
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN
to TMAX
MAX4066
MAX4066A
C, E
M
V+ = 12V,
VCOM = 0V,
VNO = 10V
TA = +25°C
nA
-100
100
ICOM(OFF)
COM Off Leakage Current
(Note 6)
-6
6
TA = TMIN
to TMAX
MAX4066
-0.1
0.1
MAX4066A
C, E
-1
1
M
V+ = 12V,
VCOM = 10V,
VNO = 10V
TA = +25°C
nA
-200
200
ICOM(ON)
COM On Leakage Current
(Note 6)
-12
12
TA = TMIN
to TMAX
MAX4066
-0.2
0.2
MAX4066A
C, E
-2
2
M
C, E
55
M
On-Resistance
RON
V+ = 12V,
ICOM = 2mA,
VNO = 10V
TA = TMIN
to TMAX
75
Note 1: Signals on NO_, COM_, or IN_ exceeding V+ or GND are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
ANALOG SWITCH