- 您現在的位置：買賣IC網 > PDF目錄351991 > 4608X-102-820 WIDERSTAND NETZWERK DICKFILM 82R 5ST PDF資料下載
參數資料
| 型號： | 4608X-102-820 |
| 英文描述： | WIDERSTAND NETZWERK DICKFILM 82R 5ST |
| 中文描述： | WIDERSTAND NETZWERK DICKFILM 82R 5ST |
| 文件頁數： | 48/62頁 |
| 文件大小： | 1883K |
| 代理商： | 4608X-102-820 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
Specifications are subject to change without notice.
328
configuration (Fig. 1) for the single-ended implementation of the
SCSI bus, or a three-resistor terminator configuration (Fig. 2) for
the differential-line version of the SCSI bus.
In the single-ended configuration, the SCSI bus is defined for
lengths up to 6 meters, while the differential-line version pro-
vides for better commonmode noise immunity over cable
lengths up to 25 meters.
The signal assignments on the single-ended SCSI bus include
8 data lines, 1 parity line, and 9 control lines. Each of these 18
lines must be terminated, and it is convenient to do this using a
resistor network which contains all of the required resistors. An
additional 32 lines are ground or power lines which do not
require termination (there are 50 lines total in the cable). In a
similar fashion, the differential configuration of the SCSI bus
uses 18 pairs of lines, each requiring termination.
As of 1989, an extended version of the SCSI standard has
been in develop-ment by ANSI, called the SCSI-2 bus. This new
standard allows for 16-bit to 32-bit wide data transfers, while
also allowing a higher bit transfer rate.
Two cables are defined in the SCSI-2 bus, termed Cable A and
Cable B, where Cable B is optional (“wide SCSI” option). Cable
A is no different than the single cable used in the original SCSI
bus, and therefore uses the same number and types of resistive
terminators (i.e., dual terminators for single-ended and triple ter-
minators for differential).
Cable B, however, is a 68-line cable, of which 29 lines (single-
ended) or 29 line-pairs (differential) require termination.
Application Guidelines
The principles of transmission-line theory apply to SCSI termi-
nators, and therefore for proper operation their placement must
be restricted to the ends of the bus and nowhere else. This
implies that the terminators should be placed as close to the
SCSI devices as possible. It is permissible to place the termina-
tor inside the SCSI device, but only if that device is located at
the end of the bus.
For disk drive applications, SCSI terminators must be present
on the host adapter card and at the disk drive end as well. Many
disk drive manufacturers have opted to design in removable
SCSI terminators into their units to account for the possibility
that their unit may not be the one at the end of the cable. For
these manufacturers, the combination of a resistor network in a
through-hole version plus a matching socket represents the only
(and expensive) alternative.
A final consideration is the cable itself. Since the terminators
are comprised of 220 ohm and 330 ohm resistors (single-ended),
the cable ideally should have a characteristic impedance which
matches the Thevenin equivalent of this resistor combination,
ance of 122 ohms would be ideal.
In addition, it is inadvisable to mix different, unmatched cables
in the same bus. Such a practice will result in undesirable signal
reflections which may compromise the integrity of the data transfer.
Bourns supplies a number of resistor network models designed
for both SCSI and SCSI-2 termination .
Cable A (SCSI and SCSI-2) Single-ended
330
220
+ 5V
GROUND
+ SIGNAL
FIGURE 1.
330
150
GROUND
- SIGNAL
FIGURE 2.
330
+ 5V
+ SIGNAL
330
5V
220
Dual
Terminators
3V
132
NO.
PACKAGE
REQ’D.
BOURNS P/N
DIP
1
4120R-3-221/331
CSIP*
2
4611X-104-221/331
CSIP*
3
4608X-104-221/331
MSIP*
3
4308R-104-221/331
Differential:
NO.
PACKAGE
REQ’D.
BOURNS P/N
4120R-820-1
DIP
2
4120R-820-2
DIP
3
4116R-8-2
CSIP*
3
4614M-8-2
MSIP
5
4310M-820-2
4120P-830-2
4420P-820-1
4420P-820-2
4420P-830-2
Cable B (SCSI-2 Only) Single-ended
NO.
PACKAGE
REQ’D.
BOURNS P/N
DIP
2
4118R-3-221/331
CSIP*
3
4612X-104-221/331
CSIP*
4
4610X-104-221/331
MSIP*
4
4310R-104-221/331
NO.
PACKAGE
REQ’D.
BOURNS P/N
DIP
4
4118R-820-2
DIP
5
4116R-8-2
CSIP*
5
4614M-820-2
MSIP*
8
4310M-820-2
*MEDIUM PROFILE (.250” SEATED HEIGHT) AND HIGH PROFILE (.350” SEATED
HEIGHT) ARE AVAILABLE BY PLACING THE LETTER “M” OR “H,” RESPECTIVELY, IN
THE FIFTH POSITION OF THE PART NUMBER.
SCSI Applications
相關PDF資料 |
PDF描述 |
|---|---|
| 4608X103 | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 4608X104 | Interface IC |
| 4609H101 | Interface IC |
| 4609H102 | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 4609H103 | Interface IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 4608X-102-820LF | 功能描述:電阻器網絡與陣列 8pins 82ohms Isolated RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
| 4608X-102-820LF | 制造商:Bourns Inc 功能描述:RESISTORS NETWORKS THICK FILM NETWORK C |
| 4608X-102-821 | 功能描述:電阻器網絡與陣列 8Pin 2% 820ohm Isolated RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
| 4608X-102-821LF | 功能描述:電阻器網絡與陣列 8pins 820ohms Isolated RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
| 4608X-102-822 | 功能描述:電阻器網絡與陣列 8Pin 2% 8.2K Isolated RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。