參數資料
型號： 514MCAXXXXXXAAG
廠商： SILICON LABORATORIES
元件分類： 時鐘產生/分配
英文描述： 250 MHz, OTHER CLOCK GENERATOR, PDSO6
封裝： 5 X 7 MM, ROHS COMPILANT PACKAGE-6
文件頁數： 2/32頁
文件大?。?/td> 267K
代理商： 514MCAXXXXXXAAG
Si514
10
Preliminary Rev. 0.9
LP2 values, in addition to updating the value of M, which requires the VCO to be recalibrated. Refer to section
depiction of the difference between small and large frequency changes.
Figure 2. Small vs Large Frequency Change Illustration
2.2. Programming a Small Frequency Change (sub ±1000 ppm)
The value of the feedback multiplier, M is the only parameter that needs to be updated for output frequency
changes less than ±1000 ppm from the center frequency (recalibrating the VCO is NOT required). This enables
the output to remain continuous during the change. For example, the output frequency can be swept continuously
between 148.5 MHz and 148.352 MHz (i.e., –0.997 ppm) with no output discontinuities or glitches by changing M
in either multiple steps or in a single step. For small frequency changes, each update of M requires 100 s to settle.
Note:
It is not possible to implement a frequency change ≥ ±1000 ppm using multiple small frequency changes
without changing the center frequency and recalibrating the VCO.
Use the following procedure to make small frequency changes:
1. If the current value of M is already known, then skip to step 2; else, using the serial port, read the current M
value (Registers 5-9).
2. Calculate the new value of M as follows (all values are in decimal format):
a. Mcurrent = M_Int + M_Frac/229 (Eq 2.2)
b. Mnew = Mcurrent x Fout_new / Fout_current (Eq 2.3)
c. M_Intnew = INT[Mnew]*
(Eq 2.4)
d. M_Fracnew = (Mnew – INT[Mnew]) x 229
(Eq 2.5)
*Where INT[n] rounds n down to the nearest integer (e.g., INT[3.9] = 3)
3. Using the I2C port, write the new value of M_Frac[23:0] (Not all registers need to be updated.)
(Registers: 5, 6, 7)
4. If necessary, write new value of M_Int[2:0] and M_Frac[28:24] register. (Register 8)
5. Write M_Int[8:3]. (Register 9) Frequency changes take effect when M_Int[8:3] is written.
Example 2.1:
An Si514 generating a 148.5 MHz clock must be reconfigured “on-the-fly” to generate a 148.352 MHz clock. This
represents a change of –0.996.633 ppm which is within the ±1000 ppm window.
1. Read the current value of M:
a. Register 5 = 0xD3 (M_Frac[7:0])
b. Register 6 = 0x65 (M_Frac[15:8])
c. Register 7 = 0x7C (M_Frac[23:16])
d. Register 8 = 0x49 (M_Int[2:0],M_Frac[28:24])
FVCO_MIN
(2080 MHz)
FVCO_MAX
(2500 MHz)
Range of small
frequency change
Programming a new center frequency requires a VCO
calibration and the output should be squelched
FCENTER
F'CENTER
Small Frequency Change
Large Frequency Change
FCENTER
+1000 ppm
FCENTER
-1000 ppm
相關PDF資料
PDF描述
514NAAXXXXXXAAGR 250 MHz, OTHER CLOCK GENERATOR, PDSO6
514NABXXXXXXBAG 170 MHz, OTHER CLOCK GENERATOR, PDSO6
514NACXXXXXXAAGR 125 MHz, OTHER CLOCK GENERATOR, PDSO6
514NACXXXXXXAAG 125 MHz, OTHER CLOCK GENERATOR, PDSO6
514NBAXXXXXXAAG 250 MHz, OTHER CLOCK GENERATOR, PDSO6
相關代理商/技術參數
參數描述
514MCC000994BAG 制造商:Silicon Laboratories Inc 功能描述:OSCILLATOR - Trays
514MLF 功能描述:時鐘發生器及支持產品 LOCO PLL CLOCK MULTIPLIER RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
514MLFT 功能描述:時鐘發生器及支持產品 LOCO PLL CLOCK MULTIPLIER RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
514NAA000776AAGR 制造商:Silicon Laboratories Inc 功能描述:OSCILLATOR - Tape and Reel
514NAA000781AAGR 制造商:Silicon Laboratories Inc 功能描述:OSCILLATOR - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*