參數資料
型號: 514PACXXXXXXAAG
廠商: SILICON LABORATORIES
元件分類: 時鐘產生/分配
英文描述: 125 MHz, OTHER CLOCK GENERATOR, PDSO6
封裝: 5 X 7 MM, ROHS COMPILANT PACKAGE-6
文件頁數: 2/32頁
文件大小: 267K
代理商: 514PACXXXXXXAAG
Si514
10
Preliminary Rev. 0.9
LP2 values, in addition to updating the value of M, which requires the VCO to be recalibrated. Refer to section
depiction of the difference between small and large frequency changes.
Figure 2. Small vs Large Frequency Change Illustration
2.2. Programming a Small Frequency Change (sub ±1000 ppm)
The value of the feedback multiplier, M is the only parameter that needs to be updated for output frequency
changes less than ±1000 ppm from the center frequency (recalibrating the VCO is NOT required). This enables
the output to remain continuous during the change. For example, the output frequency can be swept continuously
between 148.5 MHz and 148.352 MHz (i.e., –0.997 ppm) with no output discontinuities or glitches by changing M
in either multiple steps or in a single step. For small frequency changes, each update of M requires 100 s to settle.
Note:
It is not possible to implement a frequency change ≥ ±1000 ppm using multiple small frequency changes
without changing the center frequency and recalibrating the VCO.
Use the following procedure to make small frequency changes:
1. If the current value of M is already known, then skip to step 2; else, using the serial port, read the current M
value (Registers 5-9).
2. Calculate the new value of M as follows (all values are in decimal format):
a. Mcurrent = M_Int + M_Frac/229 (Eq 2.2)
b. Mnew = Mcurrent x Fout_new / Fout_current (Eq 2.3)
c. M_Intnew = INT[Mnew]*
(Eq 2.4)
d. M_Fracnew = (Mnew – INT[Mnew]) x 229
(Eq 2.5)
*Where INT[n] rounds n down to the nearest integer (e.g., INT[3.9] = 3)
3. Using the I2C port, write the new value of M_Frac[23:0] (Not all registers need to be updated.)
(Registers: 5, 6, 7)
4. If necessary, write new value of M_Int[2:0] and M_Frac[28:24] register. (Register 8)
5. Write M_Int[8:3]. (Register 9) Frequency changes take effect when M_Int[8:3] is written.
Example 2.1:
An Si514 generating a 148.5 MHz clock must be reconfigured “on-the-fly” to generate a 148.352 MHz clock. This
represents a change of –0.996.633 ppm which is within the ±1000 ppm window.
1. Read the current value of M:
a. Register 5 = 0xD3 (M_Frac[7:0])
b. Register 6 = 0x65 (M_Frac[15:8])
c. Register 7 = 0x7C (M_Frac[23:16])
d. Register 8 = 0x49 (M_Int[2:0],M_Frac[28:24])
FVCO_MIN
(2080 MHz)
FVCO_MAX
(2500 MHz)
Range of small
frequency change
Programming a new center frequency requires a VCO
calibration and the output should be squelched
FCENTER
F'CENTER
Small Frequency Change
Large Frequency Change
FCENTER
+1000 ppm
FCENTER
-1000 ppm
相關PDF資料
PDF描述
514PACXXXXXXBAG 125 MHz, OTHER CLOCK GENERATOR, PDSO6
514PBAXXXXXXAAGR 250 MHz, OTHER CLOCK GENERATOR, PDSO6
514PBAXXXXXXAAG 250 MHz, OTHER CLOCK GENERATOR, PDSO6
514PBCXXXXXXAAGR 125 MHz, OTHER CLOCK GENERATOR, PDSO6
514PBCXXXXXXBAG 125 MHz, OTHER CLOCK GENERATOR, PDSO6
相關代理商/技術參數
參數描述
514PCC000148BAG 功能描述:標準時鐘振蕩器 PROGRMABLE XO 6 PIN 0.7PS RS JTR RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列:
514REF 制造商:HellermannTyton 功能描述:Label; Refill Self-Laminating Rite-On; 3/4 in.; 5/16 in.; 200 制造商:HellermannTyton 功能描述:Rite-On Marker Refill Self-Lam 3/4(W) X 5/16(L)
514RG 制造商:MENNEKES ELECTROTECHNIK 功能描述:400V16A4P6H CONN IP44
514S4P144 功能描述:電纜組件 MINI-MZR STR EXT RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規(AWG):20, 28 長度:0.305 m 顏色:Black, Red
514S4P36 功能描述:電纜組件 MINI-MZR STR EXT RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規(AWG):20, 28 長度:0.305 m 顏色:Black, Red