www.ti.com
EVM WARNINGS AND RESTRICTIONS
SLOS538A – SEPTEMBER 2007 – REVISED OCTOBER 2007
Table 5. THS4511RGT EVM Bill of Materials
SMD
REFERENCE
PCB
MANUFACTURER'S
ITEM
DESCRIPTION
SIZE
DESIGNATOR
QTY
PART NUMBER(1)
1
CAP, 10.0
μF, Ceramic, X5R, 6.3V
0805
C3, C5
2
(AVX) 08056D106KAT2A
2
CAP, 0.1
μF, Ceramic, X5R, 10V
0402
C11, C12, C13, C14
4
(AVX) 0402ZD104KAT2A
3
CAP, 0.22
μF, Ceramic, X5R, 6.3V
0402
C15
1
(AVX) 04026D224KAT2A
4
OPEN
0402
C1, C2, C7, C8, C9, C10
6
5
OPEN
0402
R9, R10
2
6
Resistor, 49.9
, 1/16W, 1%
0402
R12
1
(KOA) RK73H1ETTP49R9F
7
Resistor, 56.2
, 1/16W, 1%
0402
R1, R2
(KOA) RK73H1ETTP56R2F
8
Resistor, 69.8
, 1/16W, 1%
0402
R11
3
(KOA) RK73H1ETTP69R8F
9
Resistor, 86.6
, 1/16W, 1%
0402
R7, R8
2
(KOA) RK73H1ETTP86R6F
10
Resistor, 340
, 1/16W, 1%
0402
R3, R4
2
(KOA) RK73H1ETTP3400F
11
Resistor, 348
, 1/16W, 1%
0402
R5, R6
2
(KOA) RK73H1ETTP3480F
12
Resistor, 0
, 5%
0805
C4, C6
2
(KOA) RK73Z2ATTD
13
Transformer, RF
T1
1
(MINI-CIRCUITS) ADT1-1WT
Jack, banana receptance, 0.25" diameter
2
14
J5, J6
(HH SMITH) 101
hole
15
OPEN
J1, J7, J8
3
16
Connector, edge, SMA PCB Jack
J2, J3
2
(JOHNSON) 142-0701-801
17
Test point, Red
TP1, TP2, TP3
3
(KEYSTONE) 5000
18
IC, THS4511
U1
1
(TI) THS4511RGT
19
Standoff, 4-40 HEX, 0.625" length
4
(KEYSTONE) 1808
20
SCREW, PHILLIPS, 4-40, 0.250"
4
SHR-0440-016-SN
21
Printed circuit board
1
(TI) EDGE# 6475513
(1)
The manufacturer's part numbers were used for test purposes only.
It is important to operate this EVM within the input and output voltage ranges as specified in the following table.
Input Range, VS+ to VS-
3.0 V to 6.0 V
Input Range, VI
3.0 V to 6.0 V NOT TO EXCEED VS+ or VS-
Output Range, VO
3.0 V to 6.0 V NOT TO EXCEED VS+ or VS-
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If
there are questions concerning the input range, please contact a TI field representative prior to connecting the
input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible
permanent damage to the EVM. Please consult the product data sheet or EVM user's guide (if user's guide is
available) prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than 30
°C. The EVM is
designed to operate properly with certain components above 50
°C as long as the input and output ranges are
maintained. These components include but are not limited to linear regulators, switching transistors, pass
transistors, and current sense resistors. These types of devices can be identified using the EVM schematic
located in the material provided. When placing measurement probes near these devices during operation, please
be aware that these devices may be very warm to the touch.
Copyright 2007, Texas Instruments Incorporated
21