參數資料
型號: 5962-8957101PA
元件分類: 光電耦合器
英文描述: 2 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 40 Mbps
封裝: HERMETIC SEALED, CERAMIC, DIP-8
文件頁數: 11/12頁
文件大?。?/td> 144K
代理商: 5962-8957101PA
8
Notes:
1. Not to exceed 5% duty factor, not to exceed 50
sec pulse width.
2. All devices are considered two-terminal devices: measured
between all input leads or terminals shorted together and all
output leads or terminals shorted together.
3. This is a momentary withstand test, not an operating condition.
4. t
PHL propagation delay is measured from the 50% point on the
rising edge of the input current pulse to the 1.5 V point on the
falling edge of the output pulse. The t
PLH propagation delay is
measured from the 50% point on the falling edge of the input
current pulse to the 1.5 V point on the rising edge of the output
pulse. Pulse Width Distortion, PWD = |t
PHL - tPLH|.
5. CM
L is the maximum slew rate of the common mode voltage that
can be sustained with the output voltage in the logic low state
(V
O(MAX) < 0.8 V). CMH is the maximum slew rate of the common
mode voltage that can be sustained with the output voltage in
the logic high state (V
O(MIN) > 2.0 V).
6. Duration of output short circuit time not to exceed 10 ms.
7. Power Supply Noise Immunity is the peak to peak amplitude of
Figure 1. Typical logic low output voltage vs. logic
low output current
Figure 2. Typical logic high output voltage vs.
logic high output current
Figure 3. Typical output voltage vs. input
forward current
Figure 4. Typical diode input forward current
characteristic
the ac ripple voltage on the V
CC line that the device will withstand
and still remain in the desired logic state. For desired logic high
state, V
OH(MIN) > 2.0 V, and for desired logic low state, VOL(MAX) < 0.8 V.
8. Measured between adjacent input pairs shorted together for each
multichannel device.
9. Each channel.
10. Standard parts receive 100% testing at 25
°C (Subgroups 1 and 9).
SMD, Class H and Class K parts receive 100% testing at 25, 125,
and –55
°C (Subgroups 1 and 9, 2 and 10, 3 and 11, respectively).
11. Parameters are tested as part of device initial characterization and
after design and process changes. Parameters are guaranteed to
limits specified for all lots not specifically tested.
12. Propagation delay skew is defined as the difference between the
minimum and maximum propagation delays for any given group
of optocouplers with the same part number that are all switching
at the same time under the same operating conditions.
13. The HCPL-6430, HCPL-6431, and HCPL-643K dual channel parts
function as two independent single channel units. Use the single
channel parameter limits.
相關PDF資料
PDF描述
5962-89571022A 2 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 40 Mbps
5962-8959827MXC 128K X 8 STANDARD SRAM, 45 ns, CDIP32
5962-8959829M7C 128K X 8 STANDARD SRAM, 25 ns, CDSO32
5962-8959835MTA 128K X 8 STANDARD SRAM, 45 ns, CDFP32
5962-8959840MUA 128K X 8 STANDARD SRAM, 20 ns, CDSO32
相關代理商/技術參數
參數描述
5962-8957101PC 功能描述:高速光耦合器 40M bit/s 1500Vdc Hermetically sealed RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube
5962-8957101XA 功能描述:高速光耦合器 40M bit/s 1500Vdc Hermetically sealed RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube
5962-8957101YA 功能描述:高速光耦合器 40M bit/s 1500Vdc Hermetically sealed RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube
5962-8957101YC 功能描述:高速光耦合器 40M bit/s 1500Vdc Hermetically sealed RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube
5962-89571022A 功能描述:高速光耦合器 40M bit/s 1500Vdc Hermetically sealed RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube