- 您現在的位置：買賣IC網 > PDF目錄68795 > 5962-8976001MXA (VISHAY SILICONIX) 8-CHANNEL, VIDEO MULTIPLEXER, PDIP28 PDF資料下載
參數資料
| 型號： | 5962-8976001MXA |
| 廠商： | VISHAY SILICONIX |
| 元件分類： | 多路復用及模擬開關 |
| 英文描述： | 8-CHANNEL, VIDEO MULTIPLEXER, PDIP28 |
| 封裝： | SDIP-28 |
| 文件頁數： | 8/17頁 |
| 文件大?。?/td> | 147K |
| 代理商： | 5962-8976001MXA |
DG534A/538A
Vishay Siliconix
www.vishay.com
16
Document Number: 70069
S-05734—Rev. G, 29-Jan-02
APPLICATIONS (CONT'D)
A typical switching threshold versus VL is shown in Figure 15.
These devices feature an address readback (Tally) facility,
whereby the last address written to the device may be output
to the system. This allows improved status monitoring and
hand shaking without additional external components.
This function is controlled by the I/O pin, which directly
addresses the tri-state buffers connected to the EN and
address pins. EN and address pins can be assigned to accept
data (when I/O = 0; WR = 0; RS = 1), or output data (when I/O =
1; WR = 1; RS = 1), or to reflect a high impedance and latched
state (when I/O = 0; WR = 1; RS = 1).
When I/O is high, the address output can sink or source
current. Note that VL is the logic high output condition. This
point must be respected if VL is varied for input logic threshold
shifting.
Further control pins facilitate easy microprocessor interface.
On chip address, data latches are activated by WR, which
serves as a strobe type function eliminating the need for
peripheral latch or memory I/O port devices. Also, for ease of
interface, a direct reset function (RS) allows all latches to be
cleared and switches opened. Reset should be used during
power up, etc., to avoid spurious switch action. See Figure 16.
Channel address data can only be entered during WR low,
when the address latches are transparent and I/O is low.
Similarly, address readback is only operational when WR and
I/O are high.
The Siliconix CLC410 Video amplifier is recommended as an
output buffer to reduce insertion loss and to drive coaxial
cables. For low power video routing applications or for unity
gain input buffers CLC111/CLC114 are recommended.
8
7
6
5
4
3
2
1
0
2468
10
12
14
16
18
Vth
(V)
VL (V)
FIGURE 15.
Switching Threshold Voltage vs. VL
Reset
Address
Decoder
WR
Video
Bus
Data
Bus
Address Bus
Data Bus
I/O
75
W
75
W
75
W
75
W
CLC410
AV = 2
CLC410
DG534A
FIGURE 16.
DG534A in a Video Matrix
WR
EN
RS
SA1
SB2
A0, A1
DA
DB
EN
WR
RS
SA1
SB2
A0, A1
DA
DB
相關PDF資料 |
PDF描述 |
|---|---|
| 5962-8980102CA | QUAD OP-AMP, 2500 uV OFFSET-MAX, CDIP14 |
| 5962-8980102CX | QUAD OP-AMP, 3500 uV OFFSET-MAX, CDIP14 |
| 5962-89801012X | QUAD OP-AMP, 1000 uV OFFSET-MAX, 2.4 MHz BAND WIDTH, CQCC20 |
| 5962-8980101CX | QUAD OP-AMP, 1000 uV OFFSET-MAX, 2.4 MHz BAND WIDTH, CDIP14 |
| 5962-8984201GX | 1-CHANNEL POWER SUPPLY SUPPORT CKT, MBCY8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962-8976001MXC | 制造商:Vishay Siliconix 功能描述:DUAL MARKED - DG538AAP/883 (MOTS) - Rail/Tube |
| 5962-8976001QXC | 制造商:Vishay Siliconix 功能描述:DESC STANDARD MILITARY DRAWING DG528AK - Rail/Tube |
| 5962-8976301M2A | 制造商:Maxim Integrated Products 功能描述:IMPROVED, DUAL, HIGH-SPEED ANALOG SWITCH - Bulk |
| 5962-8976301M2C | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| 5962-8976301MEA | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。