![](http://datasheet.mmic.net.cn/90000/5962D9569202VEX_datasheet_2945304/5962D9569202VEX_1.png)
1
File Number
3977.2
HS-0508RH, HS-0509RH
Radiation Hardened Single 8/Differential
4-Channel CMOS Analog Multiplexers
These radiation hardened monolithic CMOS multiplexers
each include an array of eight analog switches, a digital
decode circuit for channel selection, a voltage reference for
logic thresholds, and an ENABLE input for device selection
when several multiplexers are present.
The Dielectric Isolation (DI) process used in fabrication of
these devices eliminates the problem of latch-up. Also, DI
offers much lower substrate leakage and parasitic
capacitance than conventional junction-isolated CMOS.
Switches are guaranteed to break-before-make, so that two
channels are never shorted together. The switching
threshold for each digital input is established by an internal
+5V reference, providing a guaranteed minimum 2.4V for
logic “1” and maximum 0.8 for logic “0”. This allows direct
interface without pull-up resistors to signals from most logic
families: CMOS, TTL, DTL and some PMOS. For protection
against transient overvoltage, the digital inputs include a
series 200
resistor and a diode clamp to each supply. The
HS-0508RH is an eight channel single-ended multiplexer,
and the HS-0509RH is a four channel differential version. If
input overvoltage protection is needed, the HS-0548RH and
HS-0549RH multiplexers are recommended.
Specications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Specications for these devices are
contained in SMD 5962-95692. A “hot-link” is provided
on our homepage for downloading.
http://www.intersil.com/spacedefense/space.htm
Features
Electrically Screened to SMD # 5962-95692
QML Qualied per MIL-PRF-38535 Requirements
Gamma Dose . . . . . . . . . . . . . . . . . . . . . . 1 x 104RAD(Si)
No Latch-Up
No Channel Interaction During Overvoltage
Low On Resistance . . . . . . . . . . . . . . . . . . . . <200
(Typ)
44V Maximum Power Supply
Break-Before-Make Switch
Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . .
±15V
Access Time. . . . . . . . . . . . . . . . . . . . . . . . . <300ns (Typ)
Applications
Data Acquisition Systems
Control Systems
Telemetry
Pinouts
HS-0508RH GDIP1-T16 (CERDIP)
OR CDIP2-T16 (SBDIP)
TOP VIEW
HS-0509RH GDIP1-T16 (CERDIP)
OR CDIP2-T16 (SBDIP)
TOP VIEW
Ordering Information
ORDERING NUMBER
INTERNAL
MKT. NUMBER
TEMP. RANGE
(oC)
5962D9569201VEA
HS1-0508RH-Q
-55 to 125
5962D9569201VEC
HS1B-0508RH-Q
-55 to 125
5962D9569202VEA
HS1-0509RH-Q
-55 to 125
5962D9569202VEC
HS1B-0509RH-Q
-55 to 125
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
A0
ENABLE
-VSUPPLY
IN 1
IN 2
IN 3
OUT
IN 4
A1
GND
+VSUPPLY
IN 5
IN 6
IN 7
IN 8
A2
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
A0
ENABLE
-VSUPPLY
IN 1A
IN 2A
IN 3A
OUTA
IN 4A
A1
+VSUPPLY
IN 1B
IN 2B
IN 3B
IN 4B
OUT B
GND
Data Sheet
August 1999
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207
| Copyright
Intersil Corporation 1999