- 您現在的位置：買賣IC網 > PDF目錄68812 > 73S8009R-ILR (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | 73S8009R-ILR |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封裝： | SOP-28 |
| 文件頁數： | 7/23頁 |
| 文件大?。?/td> | 342K |
| 代理商： | 73S8009R-ILR |
DS_8009R_056
73S8009R Data Sheet
Rev. 1.3
15
Choice of the VCC capacitor:
Depending on the application, the requirements in terms of both the VCC minimum voltage and the
transient currents that the interface must be able to provide to the card are different. An external
capacitor must be connected between the VCC pin and the card ground in order to guarantee stability of
the LDO regulator, and to handle the transient requirements. The type and value of this capacitor can be
optimized to meet the desired specification. Table 8 shows the recommended capacitors for each VPC
power supply configuration and applicable specification.
Table 8: Choice of VCC Pin Capacitor
3.5
Over-temperature Monitor
A built-in detector monitors die temperature. When an over-temperature condition occurs, a card
deactivation sequence is initiated, and an error or fault condition is reported to the system controller via
the
OFF interrupt.
3.6
Activation and Deactivation Sequence
The host controller is fully responsible for the activation sequencing of the smart card signals CLK, RST,
I/O, AUX1 and AUX2. All of these signals are held low when the card is in the deactivated state. Upon
card activation (the fall of
CMDVCC#/CMDVCC%, all the signals will remain low until RDY goes high. The
host should set the signals RSTIN, I/OUC, CLKIN, AUX1UC and AUX2UC low prior to activating the card
and allow RDY to go high before transitioning any of these signals. In order to initiate activation, the card
must be present and there can be no over-temperature fault and no VDD fault.
CMDVCC3 or CMDVCC5
VCC
IOUC
IO
RDY
RSTIN
RST
CLKIN
CLK
Ignored
IO, AUX1, AUX2, CLK, RST are held LOW until RDY = 1 and CMDVCCx = 0
IO = IOUC if RDY=1
CLK=CLKIN if RDY=1
RST=RSTIN if RDY=1
t1
At t1 (500 s), if RDY = 0 or overcurrent, circuit will de-activate (safety feature)
VCC valid
Figure 5: Activation Sequence
Specification Requirements
System Requirements
Specification
Min VCC Voltage
allowed during
transient current
Max Transient
Current Charge
Min VPC Power
Supply required
Capacitor
Type
Capacitor
Value
EMV 4.1
4.6 V
30 nA
s
4.75 V
X5R/X7R
with
ESR<100 m
Ω
3.3 F
ISO-7816-3 &
GSM11.11
4.5 V
20 nA
s
4.75 V
1 F
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8009R-IM | SPECIALTY ANALOG CIRCUIT, QCC20 |
| 73S8009R-IL | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010C-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010C-IMR/F | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010C-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8009R-ILR/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8009R-IM/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8009R-IMR/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8010C | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Smart Card Interface |
| 73S8010C-DB | 功能描述:界面開發工具 73S8010C Demo Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。