參數資料
型號： 73S8014R-IL/F
廠商： Maxim Integrated Products
文件頁數： 10/29頁
文件大?。?/td> 0K
描述： IC SMART CARD 7816 EMV 20-SOIC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 37
控制器類型： 智能卡接口
電源電壓： 2.7 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 20-SOIC
包裝： 管件
73S8014R Data Sheet
DS_8014R_012
18
Rev. 1.0
3.6
Activation Sequence
The 73S8014R smart card interface ICs have an internal 10ms delay on the application of VDD where VDD >
VDDF. No activation is allowed during this 10ms period. The CMDVCC (edge triggered) signal must then be set
low to activate the card. In order to initiate activation, the card must be present; there can be no VDD fault.
The following steps show the activation sequence and the timing of the card control signals when the system
controller sets
CMDVCC low while the RSTIN is low:
-
CMDVCC is set low at t0.
-
VCC will rise to the selected level and then the internal VCC control circuit checks the presence of VCC at
the end of t1. In normal operation, the voltage VCC to the card becomes valid before t1. If VCC is not
valid at t1, the OFF goes low to report a fault to the system controller, and VCC to the card is shut off.
-
Turn I/O to reception mode at t2.
-
CLK is applied to the card at t3.
-
RST is a copy of RSTIN after t3.
CMDVCC
VCC
I/O
CLK
RSTIN
t
1
t
2
t
3
RST
t
0
t1 = 0.510 ms (timing by 1.5MHz internal Oscillator)
t2 = 1.5μs, I/O goes to reception state
t3 = >0.5μs, CLK starts, RST to become the copy of RSTIN
Figure 4: Activation Sequence – RSTIN Low When
CMDVCC Goes Low
The following steps show the activation sequence and the timing of the card control signals when the system
controller pulls the
CMDVCC low while the RSTIN is high:
-
CMDVCC is set low at t0.
-
VCC will rise to the selected level and then the internal VCC control circuit checks the presence of VCC at
the end of t1. In normal operation, the voltage VCC to the card becomes valid before t1. If VCC is not
valid at t1, the OFF goes low to report a fault to the system controller, and VCC to the card is shut off.
-
At the fall of RSTIN at t2, CLK is applied to the card
-
RST is a copy of RSTIN after t2.
相關PDF資料
PDF描述
73S8014RN-ILR/F IC SMART CARD 7816 EMV 20-SOIC
73S8023C-IMR/F IC SMART CARD INTERFACE 32-QFN
73S8024C-ILR/F IC SMART CARD INTERFACE 28-SOIC
73S8024RN-32IMR/F IC SMART CARD INTERFACE 32-QFN
78P2351-IGTR/F LINE INTERFACE UNIT 100-LQFP
相關代理商/技術參數
參數描述
73S8014R-ILR/F 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
73S8014R-ILR/F1 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
73S8014R-ILR/F2 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
73S8014R-ILR/F3 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
73S8014RN 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Smart Card Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*