參數資料
型號: 73S8024RN-32IMR/F
廠商: Maxim Integrated Products
文件頁數: 5/27頁
文件大?。?/td> 0K
描述: IC SMART CARD INTERFACE 32-QFN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
控制器類型: 智能卡接口
電源電壓: 2.7 V ~ 5.5 V
電流 - 電源: 2.7mA
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤
供應商設備封裝: 32-QFN(5x5)
包裝: 帶卷 (TR)
DS_8024RN_020
73S8024RN Data Sheet
Rev. 2
13
9 OFF and Fault Detection
There are two different cases that the system controller can monitor the OFF signal: to query regarding
the card presence outside card sessions, or for fault detection during card sessions.
Outside a card session: In this condition, CMDVCC is always high, OFF is low if the card is not present,
and high if the card is present. Because it is outside a card session, any fault detection will not act upon
the OFF signal. No deactivation is required during this time.
During a card session: CMDVCC is always low, and OFF falls low if the card is extracted or if any fault
detection is detected. At the same time that OFF is set low, the sequencer starts the deactivation
process.
The Figure 5 shows the timing diagram for the signals CMDVCC, PRES, and OFF during a card session
and outside the card session:
PRES
OFF
CMDVCC
VCC
outside card session
within card session
OFF
is low by
card extracted
OFF
is low by
any fault
within card
session
Figure 5: Timing Diagram – Management of the Interrupt Line OFF
10 I/O Circuitry and Timing
The states of the I/O, AUX1, and AUX2 pins are low after power on reset and they are in high when the
activation sequencer turns on the I/O reception state. See the Activation Sequence section for more
details on when the I/O reception is enabled. The states of I/OUC, AUX1UC, and AUX2UC are high after
power on reset.
Within a card session and when the I/O reception state is turn on, the first I/O line on which a falling edge
is detected becomes the input I/O line and the other becomes the output I/O line. When the input I/O line
rising edge is detected then both I/O lines return to their neutral state.
Figure 6 shows the state diagram of how the I/O and I/OUC lines are managed to become input or output.
The delay between the I/O signals is shown in Figure 7.
相關PDF資料
PDF描述
78P2351-IGTR/F LINE INTERFACE UNIT 100-LQFP
78P2351R-IMR/F IC LIU NRZ-CMI CONV 155M 56-QFN
78P2352-IELR/F IC LIU SDH SONET 2CH 128-LQFP
78Q2120C09-64CGTR/F TXRX 10/100 BASE 3.3V 64-LQFP
78Q2133/F TXRX 10/100 MDIX 3.3V IND 32-QFN
相關代理商/技術參數
參數描述
73S8024RN-DB 功能描述:界面開發工具 73S8024RN Demo Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
73S8024RN-IL 制造商:TERIDIAN 功能描述: 制造商:TDK 功能描述:SPECIALTY ANALOG CIRCUIT, 28 Pin Plastic SMT
73S8024RN-IL/F 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
73S8024RN-IL/F1 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
73S8024RN-IL/F2 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray