2006 Teridian Semiconductor Corporation Rev. 2" />
參數資料
型號: 78P2351R-IM/F
廠商: Maxim Integrated Products
文件頁數: 16/31頁
文件大?。?/td> 0K
描述: IC LIU NRZ-CMI CONV 155M 56-QFN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 260
類型: 線路接口裝置(LIU)
驅動器/接收器數: 1/1
規程: E4,OC-3,STM1-E
電源電壓: 3.15 V ~ 3.45 V
安裝類型: 表面貼裝
封裝/外殼: 56-VFQFN 裸露焊盤
供應商設備封裝: 56-QFN-EP(7x7)
包裝: 管件
78P2351R
Serial 155M
NRZ to CMI Converter
Page: 23 of 31
2006 Teridian Semiconductor Corporation
Rev. 2.1
ELECTRICAL SPECIFICATIONS (continued)
(Note 1)
0.60
0.55
0.50
0.45
0.40
0.05
-0.05
-0.50
-0.55
-0.60
-0.45
-0.40
(Note 1)
Nominal
Zero Level
(Note 2)
6.43ns
0.1ns
1ns
1.608ns
1ns
Nominal
Pulse
V
3.215ns
1.2ns
3.215ns
1.608ns
1ns
0.5ns
Note 1 – The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall into
the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more than
0.05V.
Note 2 – For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01
F, to the input of
the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input
signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any
such adjustment should be the same for both masks and should not exceed
±0.05V. This may be checked by removing the input signal again
and verifying that the trace lies with
±0.05V of the nominal zero level of the masks.
Note 3 – Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or
succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish
edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing
signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the mask,
it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be accomplished by
several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope and the pulse output
circuits with the same clock signal].
Note 4 – For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed
2ns.
Note 5 –The inverse pulse will have the same characteristics, noting that the timing tolerance at the level of the negative and positive
transitions are
± 0.1ns and ±0.5ns respectively.
Figure 9 – Mask of a Pulse corresponding to a binary One
相關PDF資料
PDF描述
MS27468T17B35PA EDR CONN RCPT 55POS JAM NUT W/PINS
V375C12M150B CONVERTER MOD DC/DC 12V 150W
VI-242-MX-F3 CONVERTER MOD DC/DC 15V 75W
MAX225EWI+TG36 IC RS-232 DRVR/RCVR 28-SOIC
MS27484T8B98PA CONN PLUG 3POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
78P2351R-IMR 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter
78P2351R-IMR/F 功能描述:接口 - 專用 Serial 155M NRZ to CMI Converter RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
78P2352 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Dual Channel OC-3/ STM1-E/ E4 LIU
78P2352-DB/CMI 功能描述:BOARD DEMO 78P2352 COAX CABLE RoHS:是 類別:編程器,開發系統 >> 評估演示板和套件 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理,電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
78P2352-DB-CMI 功能描述:界面開發工具 78P2352 Demo Brd For Coax Cable RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V