參數資料
型號： 7P320ATA2500C25
英文描述： Flash Memory Card(320M位閃速存儲器卡)
中文描述： 閃存卡（320米位閃速存儲器卡）
文件頁數： 5/62頁
文件大?。?/td> 626K
代理商： 7P320ATA2500C25
7PxxxATA25xxC25
June 2000 Rev. 1 – ECO #12936
5
White Electronic Designs Corporation
(508) 366-5151
Battery voltage detection, Digital audio output, Disk active/slave present (BVD2, -SPKR, -DASP:
input/output):
In memory card mode, BVD2 outputs the battery voltage status in the card. This card has
no battery, so this output is high level constantly. In the I/O card mode, -SPKR is held High because this
card does not have digital audio output. In True IDE Mode -DASP is the Disk Active/Slave Present signal
in the Master/Slave handshake protocol.
Reset (RESET, -RESET: input):
By assertion of the RESET signal, all registers of this card are cleared
and the RDY/-BSY signal turns to high level. In True IDE Mode -RESET is the active low hardware reset
from the host.
Wait (-WAIT, IORDY: output):
This signal outputs low level for the purpose of delaying memory access
cycle or I/O access cycle. In True IDE Mode this output signal may be used as IORDY. As for this
controller, this output is high impedance state constantly.
Input acknowledge (-INPACK: output):
This signal is not used in the memory card mode. This signal
is asserted by this card when the card is selected and responding to an I/O read cycle at the address that is
on the address bus. This signal is used for the input data buffer control. In True IDE Mode this output
signal is not used and should be kept open at the host side.
Battery voltage detection, Status change, Pass diagnostic (BVD1, -STSCHG, -PDIAG: input/output):
In the memory card mode, BVD1 outputs the battery voltage status in the card. This card has no battery, so
this output is high level constantly. In the I/O card mode, -STSCHG is used for changing the status of the
Configuration status register in the Attribute area, while the card is set I/O card interface. In True IDE
Mode, -PDIAG is the Pass Diagnostic signal in the Master/Slave handshake protocol.
V
CC
voltage sense (-VS1, -VS2: output):
These signals are intended to notify the socket of the PC Card's
CIS V
CC
requirement. -VS1 is held low and -VS2 is nonconnected in this card.
Card select (-CSEL: input):
This signal is not used in the memory card mode and I/O card mode. This
internally pulled up signal is used to configure this device as a Master or a Slave when configured in the
True IDE Mode. When this pin is grounded, this device is configured as a Master. When the pin is open,
this device is configured as a Slave.
相關PDF資料
PDF描述
7P448ATA2500C25 Flash Memory Card(448M位閃速存儲器卡)
7P512ATA2500C25 Flash Memory Card(512M位閃速存儲器卡)
7P640ATA2503C25 Flash Memory Card(640M位閃速存儲器卡)
7P1G0ATA2514C25 Flash Memory Card(1024M位閃速存儲器卡)
7S PNP 500 mA, 50 V resistor-equipped transistors R1 = 2.2 kW, R2 = 2.2 kW
相關代理商/技術參數
參數描述
7P351V330J042 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum
7P351V330K022 制造商:Cornell Dubilier Electronics 功能描述:ALUMINUM ELECTROLYTIC CAPACITOR
7P351V360A012 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum
7P351V360K022 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum
7P-38.400MBP-T 功能描述:38.4MHz Clipped Sine Wave, CMOS TCXO Oscillator Surface Mount 2.7 V ~ 5.5 V 10mA 制造商:txc corporation 系列:7P 包裝:剪切帶（CT） 零件狀態:有效 類型:TCXO 頻率:38.4MHz 功能:- 輸出:削峰正弦波，CMOS 電壓 - 電源:2.7 V ~ 5.5 V 頻率穩定度:±280ppb 工作溫度:-40°C ~ 85°C 電流 - 電源（最大值）:10mA 等級:- 安裝類型:表面貼裝 大小/尺寸:0.197" 長 x 0.126" 寬（5.00mm x 3.20mm） 高度:0.065"（1.65mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 電流 - 電源（禁用）（最大值）:- 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*