- 您現在的位置：買賣IC網 > PDF目錄358658 > 901202 AKTIVATOR N 150ML PDF資料下載
參數資料
| 型號： | 901202 |
| 英文描述： | AKTIVATOR N 150ML |
| 中文描述： | AKTIVATOR ? 150毫升 |
| 文件頁數： | 5/5頁 |
| 文件大小： | 40K |
| 代理商： | 901202 |
Technical Data Sheet
Product 7649
Worldwide Version, October 1995
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT LOCTITE CORPORATION QUALITY DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS ON SPECIFICATIONS FOR THIS PRODUCT.
ROCKY HILL, CT FAX: +1 (860)-571-5473 DUBLIN, IRELAND FAX: +353-(1)-451 - 9959
PRODUCT DESCRIPTION
LOCTITE
ACTIVATOR 7649 is a single component non-
CFC solvent based surface activator. The activator is
designed to promote the speed of cure of Loctite anaerobic
adhesives and sealants. The activator is HIGHLY
FLAMMABLE.
TYPICAL APPLICATIONS
ACTIVATOR 7649 is used where increased cure speed of
Loctite anaerobic products is required. It is especially
recommended for applications with passive metals or inert
surfaces and with large bond gaps. ACTIVATOR 7649 can
also be used when cure temperatures are below room
temperature. Use of activator is particularly recommended
for cure conditions below 15°C.
LIQUID PROPERTIES
Chemical type
Solvent
Appearance
Specific Gravity @ 25
°
C
Viscosity, 20°C, mPa.s (cP)
Flash point (TCC), °C
TLV, (ACGIH), ppm
Drying time @ 20
°
C, seconds
On part life, days
Typical Value
Basic Copper Salt
Acetone*
Clear Green liquid
0.79
2
-18 (HIGHLY FLAMMABLE)
750
30 to 70
30
Acetone is an environmentally friendly solvent.
Acetone has zero Ozone Depletion Potential.
Conforms to German WGK, category 0.
Caution
UNDER NO CIRCUMSTANCES SHOULD ACTIVATOR AND
ADHESIVE BE MIXED DIRECTLY AS LIQUIDS.
TYPICAL PERFORMANCE
Fixture time and cure speed achieved as a result of using
ACTIVATOR 7649 depend on the adhesive used and the
substrate bonded.
GENERAL INFORMATION
For safe handling information on this product, consult
the Material Safety Data Sheets, (MSDS).
HANDLING INFORMATION
Handling Precautions
Activator must be handled in a manner applicable to highly
flammable materials and in compliance with relevant local
regulations. For example, special care must be taken to
avoid contact of the activator or its vapour with naked flame
or any electrical equipment that is not flame proofed.
The carrying solvent can affect certain plastics or coatings. It
is recommended to check all surfaces for compatibility before
use.
Avoid prolonged or repeated skin contact.
Use only in a well ventilated area.
No smoking in presence of activator.
Directions for use
1.
Spray or brush on the activator on both mating surfaces to
be bonded. For small gaps treatment of only one surface
may be adequate. Contaminated surfaces may need
repeated treatment or special degreasing prior to
activation to remove any dissolvable contamination.
Porous surfaces may need two treatments of activator.
2.
Allow the solvent time to evaporate under good ventilation
until the surfaces are completely dry.
3.
After activation, parts should be bonded within one month.
Contamination of the surface before bonding should be
prevented.
4.
Apply the Loctite anaerobic product to one or both
surfaces and assemble parts immediately.
5.
Where possible, move surfaces in relation to each other
for a few seconds on assembly to properly distribute the
adhesive and for maximum activation.
6.
Secure the assembly and await fixturing before any
further handling.
Storage
This activator is classified as being HIGHLY FLAMMABLE
and therefore must be stored in an appropriate manner and in
compliance with relevant regulations. Do not store near
oxidising agents or combustible materials.
Product shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8
°
C to 28
°
C
(46
°
F to 82
°
F) unless otherwise labelled. Optimal storage is
at the lower half of this temperature range. To prevent
contamination of unused product, do not return any material
to its original container. For further specific shelf life
information, contact your local Technical Service Centre.
Note
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of
persons against any hazards that may be involved in the
handling and use thereof. In light of the foregoing, Loctite
Corporation specifically disclaims all warranties expressed or
implied, including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Loctite
Corporation’s products. Loctite Corporation specifically
disclaims any liability for consequential or incidental damages
of any kind, including lost profits. The discussion herein of
various processes or compositions is not to be interpreted as
representation that they are free from domination of patents
owned by others or as a license under any Loctite
Corporation patents which may cover such processes or
compositions. We recommend that each prospective user
test his proposed application before repetitive use, using this
data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.
相關PDF資料 |
PDF描述 |
|---|---|
| 901242 | AKTIVATOR T 150ML |
| 90130-5 | control handwheels |
| 92160-5 | KURBELRAD MIT DREHGRIFF DM160 |
| 92130-5 | KURBELRAD MIT DREHGRIFF DM130 |
| 92100-5 | KURBELRAD MIT DREHGRIFF DM100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 9012020000 | 功能描述:TOOL CRIMPER FOR COAX HTG 58-59 RoHS:是 類別:工具 >> 壓接器，施用器，壓力機 系列:- 產品培訓模塊:Board-to-Wire Connectors 標準包裝:1 系列:DF11 工具類型:臺式壓機，施用器 適用于相關產品:矩形觸點，24-28 AWG 特點:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相關產品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名稱:*AP105-DF11-2428SQ1139807AQ949366 |
| 901-20-2K | 制造商:VRN Veritron Sensor 功能描述: |
| 901-205 | 功能描述:支架與墊片 Plastic Spcr .205 in Nylon White RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
| 9012050000 | 制造商:Weidmuller 功能描述:Insulated handle SMA & SMB crimping tool |
| 9012-05-0-10 | 制造商:COTO 制造商全稱:COTO 功能描述:Miniature SIP Relays |
發布緊急采購，3分鐘左右您將得到回復。