- 您現在的位置：買賣IC網 > PDF目錄24836 > 935085330112 (NXP SEMICONDUCTORS) DATACOM, INTERFACE CIRCUIT, PDSO8 PDF資料下載
參數資料
| 型號： | 935085330112 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 網絡接口 |
| 英文描述： | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 封裝： | 3.90 MM, PLASTIC, MS-012, SOT96-1, SOP-8 |
| 文件頁數： | 16/22頁 |
| 文件大?。?/td> | 229K |
| 代理商： | 935085330112 |
PCA82C250_6
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 06 — 26 March 2009
3 of 17
NXP Semiconductors
PCA82C250
CAN controller interface
7.2 Pin description
8.
Functional description
The PCA82C250 is the interface between a CAN protocol controller and the physical bus.
It is primarily intended for high-speed automotive applications (up to 1 MBd). The device
provides differential transmit capability to the bus and differential receive capability to the
CAN controller. It is fully compatible with the
“ISO 11898” standard.
A current limiting circuit protects the transmitter output stage against short-circuit to
positive and negative battery voltage. Although the power dissipation is increased during
this fault condition, this feature will prevent destruction of the transmitter output stage.
If the junction temperature exceeds a value of approximately 160
°C, the limiting current of
both transmitter outputs is decreased. Because the transmitter is responsible for the major
part of the power dissipation, this will result in reduced power dissipation and hence a
lower chip temperature. All other parts of the PCA82C250 will remain in operation. The
thermal protection is needed, in particular, when a bus line is short-circuited.
The CANH and CANL lines are also protected against electrical transients which may
occur in an automotive environment.
Pin 8 (Rs) allows three different modes of operation to be selected: High-speed, Slope
control and Standby.
For high-speed operation, the transmitter output transistors are simply switched on and off
as fast as possible. In this mode, no measures are taken to limit the rise and fall slope.
Use of a shielded cable is recommended to avoid RFI problems. The High-speed mode is
selected by connecting pin 8 to ground.
For lower speeds or shorter bus length, an unshielded twisted pair or a parallel pair of
wires can be used for the bus. To reduce RFI, the rise and fall slope should be limited. The
rise and fall slope can be programmed with a resistor connected from pin 8 to ground. The
slope is proportional to the current output at pin 8.
If a HIGH level is applied to pin 8, the circuit enters a low-current Standby mode. In this
mode, the transmitter is switched off and the receiver is switched to a low current. If
dominant bits are detected (differential bus voltage >0.9 V), RXD will be switched to a
Table 3.
Pin description
Symbol
Pin
Description
TXD
1
transmit data input
GND
2
ground
VCC
3
supply voltage
RXD
4
receive data output
Vref
5
reference voltage output
CANL
6
LOW-level CAN voltage input/output
CANH
7
HIGH-level CAN voltage input/output
Rs
8
slope resistor input
相關PDF資料 |
PDF描述 |
|---|---|
| 935085330115 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935085330118 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935288885112 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935288885118 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935196020112 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935087-000 | 制造商:TE Connectivity 功能描述:301A511-51-05/164-0 - Bulk |
| 935087N001 | 制造商:TE Connectivity 功能描述:301A511-51-05/164-CS7092 制造商:TE Connectivity 功能描述:301A511-51-05/164-CS7092 - Bulk |
| 9350DC-200-0GZZZA | 制造商:Siemens 功能描述: |
| 9350DC-200-0ZZZTA | 制造商:Siemens 功能描述: |
| 9350DC-200-0ZZZZA | 制造商:Siemens 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。