- 您現在的位置：買賣IC網 > PDF目錄42399 > 93AA76T/SN 512 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | 93AA76T/SN |
| 元件分類： | PROM |
| 英文描述： | 512 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, MS-012, SOIC-8 |
| 文件頁數： | 19/22頁 |
| 文件大?。?/td> | 320K |
| 代理商： | 93AA76T/SN |
93AA76/86
DS21130E-page 6
2004 Microchip Technology Inc.
2.0
PRINCIPLES OF OPERATION
When the ORG pin is connected to VCC, the x16
organization is selected. When it is connected to ground,
the x8 organization is selected. Instructions, addresses
and write data are clocked into the DI pin on the rising
edge of the clock (CLK). The DO pin is normally held in
a high-Z state except when reading data from the
device, or when checking the Ready/Busy status during
a programming operation. The Ready/Busy status can
be verified during an erase/write operation by polling the
DO pin; DO low indicates that programming is still in
progress, while DO high indicates the device is ready.
The DO will enter the high-impedance state on the falling
edge of the CS.
2.1
Start Condition
The Start bit is detected by the device if CS and DI are
both high with respect to the positive edge of CLK for
the first time.
Before a Start condition is detected, CS, CLK and DI
may change in any combination (except to that of a
Start condition), without resulting in any device opera-
tion (Read, Write, Erase, EWEN, EWDS, ERAL and
WRAL). As soon as CS is high, the device is no longer
in the Standby mode.
An instruction following a Start condition will only be
executed if the required amount of opcode, address
and data bits for any particular instruction are clocked
in.
After execution of an instruction (i.e., clock in or out of
the last required address or data bit) CLK and DI
become “don't care” bits until a new Start condition is
detected.
2.2
DI/DO
It is possible to connect the Data In and Data Out pins
together. However, with this configuration it is possible
for a “bus conflict” to occur during the “dummy zero”
that precedes the read operation, if A0 is a logic high
level. Under such a condition the voltage level seen at
Data Out is undefined and will depend upon the relative
impedances of Data Out and the signal source driving
A0. The higher the current sourcing capability of A0,
the higher the voltage at the Data Out pin.
2.3
Erase/Write Enable and Disable
(EWEN, EWDS)
The 93AA76/86 powers up in the Erase/Write Disable
(EWDS) state. All programming modes must be
preceded by an Erase/Write Enable (EWEN) instruction.
Once the EWEN instruction is executed, programming
remains enabled until an EWDS instruction is executed
or VCC is removed from the device. To protect against
accidental data disturb, the EWDS instruction can be
used to disable all erase/write functions and should
follow all programming operations. Execution of a READ
instruction is independent of both the EWEN and EWDS
instructions.
2.4
Data Protection
During power-up, all programming modes of operation
are inhibited until VCC has reached a level greater than
1.4V. During power-down, the source data protection
circuitry acts to inhibit all programming modes when
VCC has fallen below 1.4V.
The EWEN and EWDS commands give additional
protection against accidentally programming during
normal operation.
After power-up, the device is automatically in the
EWDS mode. Therefore, an EWEN instruction must be
performed before any ERASE or WRITE instruction can
be executed.
相關PDF資料 |
PDF描述 |
|---|---|
| 93AA86/SN | 1K X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 93AA76A-TI/OT | 1K X 8 MICROWIRE BUS SERIAL EEPROM, PDSO6 |
| 93AA76A-TI/OTG | 1K X 8 MICROWIRE BUS SERIAL EEPROM, PDSO6 |
| 93C76A-TI/OT | 1K X 8 MICROWIRE BUS SERIAL EEPROM, PDSO6 |
| 93LC76B-TI/OT | 512 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 93AA86/P | 功能描述:電可擦除可編程只讀存儲器 1024x16-2048x8 1.8V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 93AA86/SN | 功能描述:電可擦除可編程只讀存儲器 1024x16-2048x8 1.8V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 93AA86A-I/MS | 功能描述:電可擦除可編程只讀存儲器 16K 2048 X 8 SERIAL EE,1.8V,IND RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 93AA86A-I/P | 功能描述:電可擦除可編程只讀存儲器 16K 2048 X 8 SERIAL EE,1.8V,IND RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 93AA86A-I/SN | 功能描述:電可擦除可編程只讀存儲器 16K 2048 X 8 SERIAL EE 1.8V IND RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。