- 您現(xiàn)在的位置：買賣IC網 > PDF目錄164743 > 95700 (AMPHENOL CORP) PANEL MOUNT, CABLE TERMINATED, FEMALE, BNC CONNECTOR, CRIMP, JACK PDF資料下載
參數資料
| 型號： | 95700 |
| 廠商： | AMPHENOL CORP |
| 元件分類： | RF連接器 |
| 英文描述： | PANEL MOUNT, CABLE TERMINATED, FEMALE, BNC CONNECTOR, CRIMP, JACK |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 182K |
| 代理商： | 95700 |
302
Amphenol Corporation Tel: 800-627-7100
www.amphenolrf.com
ORIGINAL CRIMP PLUGS
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 1 Install boot and slide outer ferrule onto cable as shown prior
to stripping cable.
Step 2 Strip cable jacket, braid and dielectric to dimensions shown.
See attached table for dimensions. All cuts are to be sharp
and square. Important: DO NOT nick braid, dielectric, and
center conductor when cutting. Tin center conductor using
soft solder per QQ-S-571 comp Sn 60. Avoid excessive heat
while tinning to prevent swelling of cable dielectric.
Step 3 Slightly flare out end of cable braid as so as to facilitate
insertion onto ferrule clamp nut assembly. Important:
DO NOT comb out braid.
Step 4 Install ferrule clamp nut assembly onto cable so that ferrule
portion slides under braid and insulator butts flush against
cable dielectric. Slide outer ferrule over braid and up
against nut. Make sure no slack exists in braid. Crimp outer
ferrule with tool specified in table above, keeping cable
dielectric bottomed against insulator.
Step 5 Soft solder center conductor to contact using rosin core per
QQ-S-571 comp Sn 60. DO NOT get any solder on outside
surfaces of contact.
Step 6 Screw connector body onto prepared cable termination .
Wrench tighten by holding the cable nut assembly
STATIONARY while ROTATING the connector body.
Step 7 Push body forward and into position as shown to complete
assembly.
Amphenol
Connector
Cable
Hex Crimp Data
Stripping Dimensions, inches (mm)
Number
Type
RG-/U
Cavity for
Die Set for
Contact
Outer Ferrule
Tool 227-944*
ab
c
31-351
BNC Plug
58, 141
—
.213(5.4)
227-1221-11
.922(23.4)
.516(13.1)
.250(6.3)
31-359
BNC Plug
59, 62, 140
—
.255(6.5)
227-1221-13
.922(23.4)
.516(13.1)
.250(6.3)
31-371
BNC Plug
174, 179, 187, 188, 316
—
.128(3.2)
227-1221-3
.797(20.2)
.516(13.1)
.250(6.3)
boot
ferrule
ferrule clamp
plug body assembly
nut assembly
FERRULE/
GO
SS
OUTER FERRULE
CLAMP NUT ASSY
BOOT
* for pneumatic crimp tool 227-60, use die sets indicated in this column
STEP 1
boot
outer ferrule
STEP 2
STEP 4
STEP 5
P 3
STEP 6
STEP 7
outer ferrule must
clamp nut assy
as shown
cable dielectric must
butt insulator as shown
note: center conductor must
be visible thru contact solder
hole prior to soldering
lip of boot must be firmly posi-
tioned in body groove
a
b
c
Assembly Instructions-C26b
Amphenol
BNC
相關PDF資料 |
PDF描述 |
|---|---|
| 935262441112 | ALVT SERIES, 7 1-BIT DRIVER, TRUE OUTPUT, PDSO56 |
| 935269715112 | ALVC/VCX/A SERIES, HEX 1-INPUT INVERT GATE, PDSO14 |
| 93662-501A50 | 50 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| 93662-502-08 | 8 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| 93662-502-10 | 10 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 957-009-010R011 | 功能描述:D-Sub后殼 9P-9P Gender Changer Black Shell RoHS:否 制造商:Amphenol Commercial Products 類型:Two Piece Backshell 電纜引入數量:1 電纜引入角:Straight 系列:17E 電纜直徑: 位置數量:9 外殼大小:E 外殼電鍍:Zinc |
| 957-009-010R031 | 功能描述:D-Sub后殼 9P-9P Gender Changer Gray Shell RoHS:否 制造商:Amphenol Commercial Products 類型:Two Piece Backshell 電纜引入數量:1 電纜引入角:Straight 系列:17E 電纜直徑: 位置數量:9 外殼大小:E 外殼電鍍:Zinc |
| 957-009-020R121 | 功能描述:D-Sub后殼 9P-9P Gender Changer Metal Plastic Shell RoHS:否 制造商:Amphenol Commercial Products 類型:Two Piece Backshell 電纜引入數量:1 電纜引入角:Straight 系列:17E 電纜直徑: 位置數量:9 外殼大小:E 外殼電鍍:Zinc |
| 95701 | 制造商:SIPAT 制造商全稱:SIPAT 功能描述:957MHz SAW Filter 6MHz Bandwidth |
| 957-015-010R011 | 功能描述:D-Sub后殼 15P-15P Gndr Changer Black Shell RoHS:否 制造商:Amphenol Commercial Products 類型:Two Piece Backshell 電纜引入數量:1 電纜引入角:Straight 系列:17E 電纜直徑: 位置數量:9 外殼大小:E 外殼電鍍:Zinc |
發(fā)布緊急采購，3分鐘左右您將得到回復。