- 您現在的位置：買賣IC網 > PDF目錄298733 > A1181LUA (Allegro MicroSystems, Inc.) Sensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches PDF資料下載
參數資料
| 型號： | A1181LUA |
| 廠商： | Allegro MicroSystems, Inc. |
| 元件分類： | 霍爾效應傳感器 |
| 英文描述： | Sensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| 中文描述： | 敏感雙線現場可編程斬波穩定單極霍爾效應開關 |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 356K |
| 代理商： | A1181LUA |
12
A1180-DS, Rev. 2
Worcester, Massachusetts 01615-0036 (508) 853-5000
115 Northeast Cutoff, Box 15036
www.allegromicro.com
Allegro MicroSystems, Inc.
Sensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall Effect Switches
A1180/81/82/83
PROGRAMMING PROTOCOL CHARACTERISTICS
, over operating temperature range, unless otherwise noted
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Programming Voltage1
VPL
Minimum voltage range during programming
4.5
5.0
5.5
V
VPM
11.5
12.5
13.5
V
VPH
25.0
26.0
27.0
V
Programming Current2
IPP
tr = 11 μs; 5 V → 26 V; CBYP = 0.1 μF
-
190
-
mA
Pulse Width
td(0)
OFF time between programming bits
20
-
μs
td(1)
Pulse duration for enable and addressing
sequences
20
-
μs
td(P)
Pulse duration for fuse blowing
100
300
-
μs
Pulse Rise Time
tr
VPL to VPM; VPL to VPH
5-
20
μs
Pulse Fall Time
tf
VPM to VPL; VPH to VPL
5
-
100
μs
1
Programming voltages are measured at the VCC pin.
2
A bypass capacitor with a minimum capacitance of 0.1 μF must be connected from VCC to the GND pin of the A118x device in order to
provide the current necessary to blow the fuse.
VPH
V+
t
VPM
VPL
0
Td(1)
Td(0)
Td(P)
Figure 4. Pulse amplitudes and durations
Additional information on device programming and program-
ming products is available on www. allegromicro.com. Program-
ming hardware is available for purchase, and programming
software is available free of charge.
Programming Protocol
The operate switchpoint, BOP, can be eld-programmed. To do
so, a coded series of voltage pulses through the VCC pin is used
to set bitelds in onboard registers. The effect on the device
output can be monitored, and the registers can be cleared and
set repeatedly until the required BOP is achieved. To make the
setting permanent, biteld-level solid state fuses are blown, and
nally, a device-level fuse is blown, blocking any further cod-
ing. It is not necessary to program the release switchpoint, BRP,
because the difference between BOP and BRP, referred to as the
hysteresis, BHYS, is xed.
The range of values between BOP(min) and BOP(max) is scaled to
31 increments. The actual change in magnetic ux (G) repre-
sented by each increment is indicated by BRES (see the Operating
Characteristics table; however, testing is the only method for
verifying the resulting BOP). For programming, the 31 incre-
ments are individually identied using 5 data bits, which are
physically represented by 5 bitelds in the onboard registers.
By setting these bitelds, the corresponding calibration value is
programmed into the device.
Three voltage levels are used in programming the device: a low
voltage, VPL , a minimum required to sustain register settings; a
mid-level voltage, VPM , used to increment the address counter
in the device; and a high voltage, VPH , used to separate sets of
VPM pulses (when short in duration) and to blow fuses (when
long in duration). A fourth voltage level, essentially 0 V, is used
to clear the registers between pulse sequences. The pulse values
are shown in the Programming Protocol Characteristics table and
in gure 4.
Code Programming.
Each biteld must be individually set. To
do so, a pulse sequence must be transmitted for each biteld that
is being set to 1. If more than one biteld is being set to 1, all
pulse sequences must be sent, one after the other, without allow-
ing VCC to fall to zero (which clears the registers).
The same pulse sequence is used to provisionally set bitelds as
is used to permanently set biteld-level fuses. The only differ-
ence is that when provisionally setting bitelds, no fuse-blowing
pulse is sent at the end of the pulse sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| A11A-10-B-D-1 | 10 CONTACT(S), MALE, DIP CONNECTOR, IDC, PLUG |
| A1301KUA | Continuous-Time Ratiometric Linear Hall Effect Sensors |
| A201MD9AB | TOGGLE SWITCH, DPDT, LATCHED, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE |
| A22-DR02A | PUSHBUTTON SWITCH, DPST, LATCHED, PANEL MOUNT |
| A22-DR11M | PUSHBUTTON SWITCH, SPST, MOMENTARY, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1181LUA-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Sensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1182 | 制造商:Quick 功能描述:BQFP 24 X 24 NOZZLE FOR QUICK957/957D |
| A118-2 | 功能描述:SWITCH HARDWARE RoHS:是 類別:開關 >> 配件 - 帽蓋 系列:800 標準包裝:1 系列:AP 開關類型:按鈕 形狀:圓形，凸起（圓頂） 顏色:紅 發光:發光開口 適用于相關產品:AP 系列 安裝類型:卡入式 尺寸:12.35mm 直徑 x 6.25mm H 特點:- 配用:AP2N006TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N003TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N002TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N006SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N003SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N002SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP4N007SWBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N007TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N007SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP4N006TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125V更多... 其它名稱:*481D03001 |
| A11826-000 | 制造商:TE Connectivity 功能描述:55A1132-20-5/6/9-9 - Cable Rools/Shrink Tubing |
| A1182ELH | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Two-Wire, Programmable, Chopper-Stabilized, Unipolar Hall-Effect Switch |
發布緊急采購，3分鐘左右您將得到回復。
