- 您現在的位置：買賣IC網 > PDF目錄361984 > A132A IC PDF資料下載
參數資料
| 型號： | A132A |
| 英文描述： | IC |
| 中文描述： | 集成電路 |
| 文件頁數： | 2/31頁 |
| 文件大?。?/td> | 226K |
| 代理商： | A132A |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
SPECIFYING QUARTZ CRYSTALS
A typical quartz crystal specification reads like this:
35.0MHz HC49 15 30 20 SR 3RD BU T
Frequency
Holder Style
Frequency Tolerance at 25°C
Frequency Stability
Lower end of Operating Temp Range
Circuit Condition
Overtone order
Packaging
Additional Text Code (for non-standard product)
Thefollowingnotesdefineeachelementofthespecification.
Frequency
Frequency is normally specified in kilohertz (kHz) up to
999.999kHz and in megahertz (MHz) from 1.0MHz. All
our computer-generated transaction documents follow this
standard convention automatically.
Thefrequencyshouldbegiventosevensignificantfigures.If
seven significant figures are not used, any figure that might
follow those given will be taken as zero. Thus a frequency
given as 16.6MHz will be taken as 16.60, not 16.66667.
Some specifiers extend the use of kHz to all crystals
operating in fundamental mode, reserving MHz for
overtones. To minimise the possibility of misunderstanding
it is best to use the standard method and specify the mode.
Holder Style
Before manufacture of the crystal can start, the holder style
must be defined. If the holder size is not known or it is
unimportant,wewillsupplytheholdernormallyadoptedfor
the frequency specified, such as HC49 for the majority of
microprocessorapplications.Theholderinformationshould
alsocoveranymechanicalvariantrequiredsuchasatopwire
or cropped leads. The following variants for example are
available for most crystals, either singly or in some cases, in
combination:
3 lead base
Top wire
Insulating sleeve
Taped and reeled
Fitted insulator
Cropped leads
Formed leads
Frequency Tolerance
The cost of manufacture depends partly on the accuracy
required at the reference temperature (which in the case of
the AT-cut crystal, is usually 25°C).
Where high initial accuracy is important the additional
manufacturing cost should be weighed against the cost of
includingafrequencytrimmingfacilitywithintheoscillator.
Frequency Stability
Frequency stability is normally specified as a frequency
tolerance over a defined operating temperature range with
respect to the frequency at reference temperature. The
temperature ranges are defined for each crystal in the
relevant data sheet. However the majority of crystals will
continue to operate quite satisfactorily outside the
temperature range for which they are specified, but with a
possible degradation of their frequency stability.
Generalised frequency vs temperature curves for the AT-cut
crystal types are illustrated in the following pages. These
indicate that, without compensation, a crystal specified for
operation over a wide frequency range will probably have an
inferior performance over a narrower range than one whose
design was optimised for the narrower range. The angle of
cut of the quartz blank from its quartz stone determines
which curve will be followed; the chosen angle being subject
to its own tolerance. Thus, since manufacturing cost is
tolerance-dependent it is wise not to specify a wider
operating temperature range than is actually needed unless
some sacrifice of stability, or an increase in cost, can be
accepted.
Standard Frequency Tolerances and Stabilities
±5ppm, ±10ppm, ±15ppm, ±20ppm, ±30ppm,
±50ppm, ±100ppm
Operating Temperature Ranges
0 to 50°C
–10 to 60°C
–20 to 70°C
–30 to 80°C
–40 to 90°C
–55 to 105°C
–55 to 125°C
When the required temperature range is symmetrical about
25°C, it is indicated in the specification by the lower figure,
ie: –20 to 70°C would read ‘20’ as shown in the example. If
the required temperature range is not symmetrical about
25°C, both figures are used, ie: –55 to 85°C and appear in
the additional text code section (T).
Circuit condition
The characters ‘SR’ are used to denote calibration of the
crystal at series resonance. If it is to be calibrated at load
resonance the characters represent the circuit load
capacitance in pF.
Packaging Codes
Tape & Reel packaging is available as an option on many of
the products outlined in the Quartz Crystal chapter.
EuropeTel:+44(0)146074433
Fax:+44(0)146072578
2
Americas Tel:+19199410430
Fax:+19199410530
Q
C
相關PDF資料 |
PDF描述 |
|---|---|
| A132B | IC |
| A133A | IC |
| A134B | IC |
| A135A | IC |
| A140A | IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A132B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC |
| A132K | 制造商:IQD Frequency Products 功能描述:CRYSTAL 6.000000MHZ |
| A132S | 制造商:IQD Frequency Products 功能描述:CRYSTAL SMD 6.00MHZ |
| A-132X | 制造商:Triad Magnetics 功能描述: |
| A133 | 功能描述:100 SERIES HANGER RoHS:是 類別:測試設備 >> 配件 系列:100 標準包裝:1 系列:Anaheim Scientific 類型:專用 附件類型:三腳架 適用于相關產品:儀表 技術規格:- 配用:BK725-ND - DATALOG HUMID/TEMP METER W/DL INBK720-ND - HUMIDITY/TEMP METER W/DUAL INPUT 其它名稱:BKTRISND |
發布緊急采購，3分鐘左右您將得到回復。