- 您現在的位置：買賣IC網 > PDF目錄67355 > A1381LLHLT-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | A1381LLHLT-T |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT |
| 封裝： | SOT-23W, 3 PIN |
| 文件頁數： | 6/19頁 |
| 文件大小： | 391K |
| 代理商： | A1381LLHLT-T |
Programmable Linear Hall Effect Sensor ICs with Analog Output
Available in a Miniature Thin Profile Surface Mount Package
A1381, A1382,
A1383, and A1384
14
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Try Mode
Try mode allows a single programmable parameter to be tested
without permanently setting its value. Multiple parameters cannot
be tested simultaneously in this mode. After powering the VCC
supply, select the desired parameter register and address its bit
field. When addressing the bit field, each VPM pulse increments
the value of the parameter register, up to the maximum possible
code (see Programming Logic table). The addressed parameter
value remains stored in the device even after the programming
drive voltage is removed from the VOUT pin, allowing the value
to be measured. Note that for accurate time measurements, the
blow capacitor, CBLOW, should be removed during output voltage
measurement.
It is not possible to decrement the value of the register without
resetting the parameter bit field. To reset the bit field, and thus the
value of the programmable parameter, cycle the supply (VCC) voltage.
Blow Mode
After the required value of the programmable parameter is found
using Try mode, its corresponding code should be blown to make
its value permanent. To do this, select the required parameter
register, and address and blow each required bit separately (as
described in the Fuse Blowing section). The supply must be
cycled between blowing each bit of a given code. After a bit is
blown, cycling the supply will not reset its value.
Lock Mode
To lock the device, address the LOCK bit and apply a blow pulse
with CBLOW in place. After locking the device, no future pro-
gramming of any parameter is possible.
Programming Modes
相關PDF資料 |
PDF描述 |
|---|---|
| A1384LUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
| A1383EUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
| A1382EUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
| A1382LLHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT |
| A1392SEHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 3.1V, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1381LLHLX-T | 制造商:Allegro MicroSystems 功能描述:LIMITED FIELD PROGRAMMABLE LIN 制造商:ALLEGRO MICROSYSTEMS, LLC 功能描述:IC HALL EFFECT SENSOR SOT-23W |
| A1381LUA-T | 功能描述:IC SENSOR HALL EFFECT PREC 3-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:A138x 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1381LUATI-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1382 | 制造商:HAKKO Corporation 功能描述: |
| A1382ELHLT-T | 功能描述:IC SENSOR HALL EFFECT SOT-23W RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:A138x 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。