- 您現在的位置：買賣IC網 > PDF目錄67355 > A1384LUA-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | A1384LUA-T |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | SIP-3 |
| 文件頁數： | 5/19頁 |
| 文件大?。?/td> | 391K |
| 代理商： | A1384LUA-T |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
Programmable Linear Hall Effect Sensor ICs with Analog Output
Available in a Miniature Thin Profile Surface Mount Package
A1381, A1382,
A1383, and A1384
13
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
in figure 3, decimal code 5 is equivalent to the binary number
101. Therefore bit 2 (code 4) must be addressed and blown, the
device power supply cycled, and then bit 0 (code 1) addressed
and blown. An appropriate sequence for blowing code 5 is shown
in figure 4. The order of blowing bits, however, is not important.
Blowing bit 0 first, and then bit 2 is acceptable.
Note: After blowing, the programming is not reversible, even
after cycling the supply power. Although a register bit field fuse
cannot be reset after it is blown, additional bits within the same
register can be blown at any time until the device is locked. For
example, if bit 1 (binary 10) has been blown, it is still possible to
blow bit 0. The end result would be binary 11 (decimal code 3).
Locking the Device
After the desired code for each parameter is programmed, the
device can be locked to prevent further programming of any
parameters.
Additional Guidelines
The additional guidelines in this section should be followed to
ensure the proper behavior of these devices:
A 0.1 μF blowing capacitor, C
BLOW, must be mounted between
the VOUT pin and the GND pin during programming, to ensure
enough current is available to blow fuses.
The C
BLOW blowing capacitor must be replaced in the final
application with a suitable CL. (The maximum load capacitance
is 10 nF for proper operation.)
The power supply used for programming must be capable of
delivering at least 26 V and 300 mA.
Be careful to observe the t
LOW delay time before powering
down the device after blowing each bit.
The following programming order is recommended:
POL
1.
TC
2.
SENS
Sens
3.
V
4. OUT(Q)
LOCK (only after all other parameters have been pro-
5.
grammed and validated, because this prevents any further
programming of the device)
Figure 4. Example of programming pulses applied to the VOUT pin that
result in permanent parameter settings. In this example, the register cor-
responding to key 1 is selected and code 5 is addressed and blown.
V+
0
Register
Selection
(Key 1)
VCC = 0 V
Register
Selection
(Key 1)
Addressing
VP(HIGH)
VP(MID)
VP(LOW)
Programming of Code 5 in Key 1
(Code 4)
Addressing
(Code 1)
(Code 4 in
Key 1)
Blow
tBLOW
(Code 1 in
Key 1)
Blow
VCC = 0 V
Figure 3. Example of code 5 broken into its binary components, which are
code 4 and code 1.
(Decimal Equivalent)
Code 5
Bit Field Selection
Address Code Format
Code in Binary
Fuse Blowing
Target Bits
Fuse Blowing
Address Code Format
(Binary)
1 0 1
Bit 2
Bit 0
Code 4
Code 1
(Decimal Equivalents)
相關PDF資料 |
PDF描述 |
|---|---|
| A1383EUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
| A1382EUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
| A1382LLHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT |
| A1392SEHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 3.1V, RECTANGULAR, SURFACE MOUNT |
| A1393SEHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 3.1V, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1384LUATI-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1385 | 制造商:HAKKO Corporation 功能描述: |
| A13855-0001 | 制造商:RAF Electronic Hardware 功能描述: |
| A1386 | 制造商:HAKKO Corporation 功能描述: |
| A1386LLHLT-T | 功能描述:IC HALL EFFECT SENSOR 5V SOT-23W RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:A138x 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。