- 您現在的位置：買賣IC網 > PDF目錄164966 > A165S-T2M-1 ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 3A, 30VDC, PANEL MOUNT PDF資料下載
參數資料
| 型號： | A165S-T2M-1 |
| 元件分類： | 開關 |
| 英文描述： | ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 1920K |
| 代理商： | A165S-T2M-1 |
A165S/W
15
Safety Precautions
Refer to Safety Precautions for All Pushbutton Switches.
Do not apply a voltage between the incandescent
lamp and the terminal that is greater than the rated
voltage. If the incandescent lamp is broken, the
operating part may pop out.
Always turn OFF the power and wait for 10 minutes
before replacing the incandescent lamp. If the lamp is
replaced immediately after the power is turned OFF,
the remaining heat may cause burns.
Mounting
Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance.
Do not tighten the mounting nut more than necessary using tools
such as pointed-nose pliers. Doing so will damage the mounting
nut.
The tightening torque is 0.29 to 0.49 Nm.
Wiring
Solder terminals and quick-connect terminals (#110) are commonly
used for terminals.
Be sure to use electrical wires that are a size appropriate for the
applied voltage and carry current (conductor size is 0.5 to 0.75
mm2). Perform soldering according to the conditions provided
below. If the soldering is not properly performed, the lead wires will
become detached, resulting in short-circuits.
1. Hand soldering: 350
°C, within 3 s
2. Dip soldering: 350
°C, within 3 s
Wait for one minute after soldering before exerting any external
force on the solder.
Use non-corrosive resin fluid as the flux.
Make sure that the electric cord is wired so that it does not touch
the Unit. If the electric cord touches the Unit, then electric wires with
a heat resistance of 100
°C min. must be used.
After wiring the Switch, maintain an appropriate clearance and
creepage distance.
Operating Environment
The IP65 model is designed with a degree of protection so that it
will not sustain damage if it is subjected to water from any direction
to the front of the panel.
Using the Microload
Insert a contact protection circuit, if necessary, to prevent the
reduction of life expectancy due to extreme wear on the contacts
caused by loads where inrush current occurs when the contact is
opened and closed.
The A16 allows both a standard load (125 V at 5A, 250 V at 3 A)
and a microload. If a standard load is applied, however, the
microload area cannot be used. If the microload area is used with a
standard load, the contact surface will become rough, and the
opening and closing of the contact for a microload may become
unreliable.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% (
λ 60) (conforming to JIS C5003).
The equation,
λ 60 = 0.5 × 10-4/operations indicates that the
estimated malfunction rate is less than 1/2,000,000 operations with
a reliability level of 60%.
LED
The LED current-limiting resistor is built-in, so external resistance
is not required.
WARNING
Precautions for Correct Use
Rated voltage
Internal limiting resistor
5 VDC
Red, yellow: 300
Green: 160
12 VAC/VDC
Red, yellow: 1 k
Green: 910
24 VAC/VDC
2.4 k
Invalid
area
0.1
1
10
100
1,000
1 mA
5
12
24
30
0.15 mA
Current (mA)
V
oltage
(V)
0
Microload area
相關PDF資料 |
PDF描述 |
|---|---|
| A18-10 | COPPER ALLOY, TIN FINISH, RING TERMINAL |
| A1PCA0X320L103 | PUSHBUTTON SWITCH, 4PDT, LATCHED, 6A, 12VDC, PANEL MOUNT-THREADED |
| A1PCA0X120I103 | PUSHBUTTON SWITCH, SPDT, LATCHED, 6A, 12VDC, PANEL MOUNT-THREADED |
| A1PCA0Y220L103 | PUSHBUTTON SWITCH, DPDT, MOMENTARY, 6A, 12VDC, PANEL MOUNT-THREADED |
| A1PCA1Y120H103 | PUSHBUTTON SWITCH, SPDT, MOMENTARY, 6A, 12VDC, PANEL MOUNT-THREADED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A165ST2M2 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNOB ROUND ALT 2POS DPDT 制造商:Omron Electronic Components LLC 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Selector N.O./N.C. DPDT 90° Knob 5A 250VAC 30VDC Solder 250000Cycles Panel Mount |
| A165S-T2M-2 | 功能描述:旋鈕開關 RND 2 PS MAINT KNOB IP65 DPDT RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
| A165ST3A | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH UNIT ROUND MOM 3POS BLACK 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Selector Switch Round Operator |
| A165S-T3A | 功能描述:旋鈕開關 KNOB-TYPE RND 3POS MOM SELECTOR SWITCH RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
| A165ST3A2 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNOB RND 3POS DPDT 制造商:Omron Electronic Components LLC 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A |
發布緊急采購，3分鐘左右您將得到回復。