• <em id="ulwb2"></em><dl id="ulwb2"></dl>
    <nobr id="ulwb2"><sup id="ulwb2"><tr id="ulwb2"></tr></sup></nobr>
    <rt id="ulwb2"><pre id="ulwb2"><fieldset id="ulwb2"></fieldset></pre></rt>
  • <label id="ulwb2"></label>
    <label id="ulwb2"></label>
  • 參數資料
    型號: A22L-CW-T2-10M
    元件分類: 開關
    英文描述: PUSHBUTTON SWITCH, SPST, MOMENTARY, PANEL MOUNT
    文件頁數: 38/48頁
    文件大小: 1531K
    代理商: A22L-CW-T2-10M
    Common To All Assemblies
    Common To All Assemblies
    44
    Removing the Switch Unit
    Insert a screwdriver between the Mounting Latch and the Switch
    Unit, then push down the screwdriver in the direction indicated by
    the arrow in the following figure.
    Use either of the following screwdrivers.
    Flat-head
    screwdriver
    Screwdriver
    Phillips
    screwdriver
    J
    WIRING
    Wiring Round Crimp Terminals
    Loosen the terminal screw from the Switch Unit until it completely
    comes off the groove, insert a screwdriver as shown in the following
    figure, then push up the washer in the direction indicated by the
    arrow to temporarily secure it. Now, a round crimp terminal can be
    connected. After inserting the terminal, tighten the screws to com-
    plete wiring.
    Screw
    Washer
    Screwdriver
    J
    ENGRAVING
    Engrave the characters on the surface on the Cap. Make sure
    that the characters are aligned parallel to the imaginary line
    connecting the two protruding portions to the left and right of the
    Cap.
    The characters must not be engraved deeper than 0.5 mm. Apply
    an alcohol-based paint coating, such as melamine, alkyd, or
    acrylic resin paint coating, to the engraved characters.
    Protruding portions on Cap
    J
    AFFIXING CHARACTER FILM
    Hold the Cap, remove the cardboard on the Film, and attach the Film
    to the Cap. Make sure that the protruding portions of the Cap en-
    gage the cutout portions of the Film and that the characters are
    aligned parallel to the imaginary line connecting the two protruding
    portions to the left and right of the Cap.
    Protruding portions on Cap
    Remove the cardboard.
    J
    MOUNTING AND DISMOUNTING
    SNAP-IN LEGEND
    Press and secure the Snap-in Legend Plate onto the Legend
    Plate Frame.
    The direction of the characters will vary with the mounting
    direction of the control panel if the Switch is a knob or key
    selector model.
    Legend Plate Frame
    Snap-in Legend Plate
    Concave surface
    相關PDF資料
    PDF描述
    A22-CA-20M PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT
    A22-GA-01M PUSHBUTTON SWITCH, SPST, MOMENTARY, PANEL MOUNT
    A22-GA-10M PUSHBUTTON SWITCH, SPST, MOMENTARY, PANEL MOUNT
    A22-GY-11M PUSHBUTTON SWITCH, SPST, MOMENTARY, PANEL MOUNT
    A22-CR-01A PUSHBUTTON SWITCH, SPST, LATCHED, PANEL MOUNT
    相關代理商/技術參數
    參數描述
    A22LCWT211A 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O./N.C. DPST Square Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount
    A22L-CW-T2-11A 功能描述:按鈕開關 SPST-NO+NC SQ 220 WH IP65 LED Ill ext act RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
    A22LCWT211M 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O./N.C. DPST Square Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount
    A22L-CW-T2-11M 功能描述:按鈕開關 SPST-NO+NC SQ 220 WH IP65 LED Ill ext act RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
    A22LCWT220A 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST-NO 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O. DPST Square Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount