- 您現在的位置：買賣IC網 > PDF目錄164967 > A22L-TG-12A-10M PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED PDF資料下載
參數資料
| 型號： | A22L-TG-12A-10M |
| 元件分類： | 開關 |
| 英文描述： | PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
| 文件頁數： | 17/30頁 |
| 文件大?。?/td> | 5020K |
| 代理商： | A22L-TG-12A-10M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
A22
24
Application
Mounting to the Panel
Panel Hole Dimensions
Panel hole dimensions are given below.
Recommended panel thickness: 1 to 5 mm.
For 25-dia. holes, always use 25-dia. Rings. (Since the cutout
dimensions are large, IP65 cannot be guaranteed unless 25-dia.
Rings are used.)
If outer surface treatment such as coating is performed for the
panel, the panel dimensions after outer surface treatment must
meet the specified panel dimensions.
Matrix Installation
1. The following panel hole dimensions
apply when Switch Unit and the
Standard-size Legend Plate Frame and
Lock Ring are mounted, and lead wires
are connected directly to the Switch
Block.
2. The following panel hole dimensions
apply when the Large-size Legend Plate Frame is mounted, and
when crimp terminals are connected to the Switch Block terminals.
For 1. above:
For 2. above:
Note: 1. The above dimensions are the minimum dimensions for when the wires
described under Applicable Wire Size on page 23 are used. If a
different wires are used, the wiring dimensions may be different so
determine an appropriate pitch before setup.
2. With pushbuttons of external dimensions greater than 30 mm, set the
pitch according to the dimensions. (When using matrix installation for
the A22-M
@, mount with a pitch of 40 mm instead of 30 mm in the
diagram above.)
Mounting the Operation Unit on the Panel
Insert the Operation Unit (Pushbutton, etc.) from the front surface of the
panel, insert the Lock Ring and the mounting nut from the terminal side,
then tighten the nut. Before tightening, check that the rubber washer is
present between the Pushbutton Unit and the panel.
When using a Legend Plate Frame, put one rubber washer each
between the Legend Plate Frame and the panel and between the
Operation Unit and the Legend Plate Frame. (One rubber washer
will be provided when one Legend Plate Frame is ordered.)
Align the Lock Ring with the groove in the casing, then insert the
Lock Ring so that its edge is located on the panel side.
22.3
+0.4
0
+0.2
0
+0.4
0
22.3
25 dia.
22 dia.
+0.4
0
25
+0.5
0
3.2
24.1
0.8R
max.
Not Using a Lock Ring
Using a Lock Ring
Switch Blocks
A
A22-10, A22-10S
A22-01, A22-01S
45 mm min.
A22-20, A22-20S, A22-02
A22-02S, A22-11, A22-11S
55 mm min.
Type of crimp terminal
Switch Blocks
B
Bare crimp terminals
A22-10, A22-10S
A22-01, A22-01S
51 mm min.
A22-20, A22-20S, A22-02
A22-02S, A22-11, A22-11S
61 mm min.
Crimp terminals with
insulating sheath
A22-10, A22-10S
A22-01, A22-01S
60 mm min.
A22-20, A22-20S, A22-02
A22-02S, A22-11, A22-11S
70 mm min.
30
A
30
B
Pitches A and B between the centers of the mounting holes are as follows:
相關PDF資料 |
PDF描述 |
|---|---|
| A22L-TG-6A-01A | PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
| A22L-CR-24A-11A | PUSHBUTTON SWITCH, DPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
| A22L-CR-T2-11A | PUSHBUTTON SWITCH, DPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
| A22L-GR-6A-10A | PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
| A22L-HG-24A-11M | PUSHBUTTON SWITCH, DPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A22LTG12A11A | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O./N.C. DPST Round Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount |
| A22L-TG-12A-11A | 功能描述:按鈕開關 SPST-NO+NC RN 12V GN IP65 LED ext act RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| A22LTG12A11M | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O./N.C. DPST Round Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount |
| A22L-TG-12A-11M | 功能描述:按鈕開關 SPST-NO+NC RN 12V GN IP65 LED ext act RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| A22LTG12A20A | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST-NO 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O. DPST Round Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount |
發布緊急采購，3分鐘左右您將得到回復。