- 您現在的位置：買賣IC網 > PDF目錄379533 > A54SX08P-3TQ208I (Electronic Theatre Controls, Inc.) 54SX Family FPGAs PDF資料下載
參數資料
| 型號： | A54SX08P-3TQ208I |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | FPGA |
| 英文描述： | 54SX Family FPGAs |
| 中文描述： | 54SX家庭的FPGA |
| 文件頁數： | 12/57頁 |
| 文件大?。?/td> | 415K |
| 代理商： | A54SX08P-3TQ208I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
5 4 S X F a m ily F P G A s
12
v3.1
A 54S X 16P A C S pe c ific a tions for (P C I Ope ra tion)
Symbol
Parameter
Condition
0 < V
OUT
≤
1.4
1
1.4
≤
V
OUT
< 2.4
1, 2
Min.
Max.
Units
I
OH(AC)
Switching Current High
–44
mA
mA
–44 + (V
OUT
– 1.4)/0.024
3.1 < V
OUT
< V
CC1, 3
Equation A: on
page 13
–142
(Test Point)
V
OUT
= 3.1
3
V
OUT
≥
2.2
1
2.2 > V
OUT
> 0.55
1
mA
mA
I
OL(AC)
Switching Current High
95
V
OUT
/0.023
0.71 > V
OUT
> 0
1, 3
Equation B: on
page 13
206
mA
(Test Point)
Low Clamp Current
Output Rise Slew Rate
Output Fall Slew Rate
V
OUT
= 0.71
3
–5 < V
IN
≤
–1
0.4V to 2.4V load
4
2.4V to 0.4V load
4
mA
mA
V/ns
V/ns
I
CL
slew
R
slew
F
Notes:
1.
–25 + (V
IN
+ 1)/0.015
1
1
5
5
Refer to the V/I curves in
Figure8
. Switching current characteristics for REQ#and GNT#are permitted to be one half of that specified here;
i.e., half size output drivers may be used on these signals. This specification does not apply to CLK and RST#which are system outputs.
“Switching Current High” specification are not relevant to SERR# INTA# INTB# INTC# and INTD#which are open drain outputs.
Note that this segment of the minimum current curve is drawn from the AC drive point directly to the DC drive point rather than toward
the voltage rail (as is done in the pull-down curve). This difference is intended to allow for an optional N-channel pull-up.
Maximum current requirements must be met as drivers pull beyond the last step voltage. Equations defining these maximums (A and B)
are provided with the respective diagrams in
Figure8
. The equation defined maxima should be met by design. In order to facilitate
component testing, a maximum current test point is defined for each side of the output driver.
This parameter is to be interpreted as the cumulative edge rate across the specified range, rather than the instantaneous rate at any point
within the transition range. The specified load (diagram below) is optional; i.e., the designer may elect to meet this parameter with an
unloaded output per revision 2.0 of the PCI Local Bus Specification. However, adherence to both maximum and minimum parameters is
now required (the maximum is no longer simply a guideline). Since adherence to the maximum slew rate was not required prior to
revision 2.1 of the specification, there may be components in the market for some time that have faster edge rates; therefore, motherboard
designers must bear in mind that rise and fall times faster than this specification could occur, and should ensure that signal integrity
modeling accounts for this. Rise slew rate does not apply to open drain outputs.
2.
3.
4.
output
buffer
1/2 in. max.
V
CC
1k
10 pF
1k
pin
相關PDF資料 |
PDF描述 |
|---|---|
| A54SX08P-3TQ208M | 54SX Family FPGAs |
| A54SX08P-3TQ208PP | 54SX Family FPGAs |
| A54SX08P-3VQ208 | 54SX Family FPGAs |
| A54SX16 | Quad 2-input positive-NAND gates 14-SO 0 to 70 |
| A54SX32 | Quad 2-input positive-NAND gates 8-SO 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A54SX08P-3TQ208M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs |
| A54SX08P-3TQ208PP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs |
| A54SX08P-3TQG208 | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:SX Family FPGAs |
| A54SX08-P-3TQG208I | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:SX Family FPGAs |
| A54SX08P-3TQG208I | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:SX Family FPGAs |
發布緊急采購，3分鐘左右您將得到回復。