- 您現在的位置：買賣IC網 > PDF目錄223306 > ACPL-072L-500E 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 25 Mbps PDF資料下載
參數資料
| 型號： | ACPL-072L-500E |
| 元件分類： | 光電耦合器 |
| 英文描述： | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 25 Mbps |
| 封裝： | ROHS COMPLIANT, SURFACE MOUNT, SOP-8 |
| 文件頁數： | 2/11頁 |
| 文件大?。?/td> | 286K |
| 代理商： | ACPL-072L-500E |
10
Application Information
Bypassing and PC Board Layout
The ACPL-x72L optocouplers are extremely easy to use.
No external interface circuitry is required because ACPL-
x72L uses high speed CMOS IC technology allowing
CMOS logic to be connected directly to the inputs and
outputs.
As shown in Figure 7, the only external components
required for proper operation are two bypass capacitors.
Capacitor values should be between 0.01mF and 0.1mF.
For each capacitor, the total lead length between both
ends of the capacitor and power supply pins should not
exceed 20mm. Figure 8 illustrates the recommended
printed circuit board layout for ACPL-x72L.
Figure 7. Recommended Circuit Diagram
Figure 8. Recommended Printed Circuit Board Layout
Propagation Delay, Pulse-Width Distortion and Propa-
gation Delay Skew
Propagation Delay is a figure of merit which describes
how quickly a logic signal propagates through a system.
The propagation delay from a low to high (tPLH) is the
amount of time required for an input signal to propagate
to the output, causing the output to change from low to
high. Similarly, the propagation delay from high to low
(tPHL) is the amount of time required for the input signal
to propagate to the output, causing the output to change
from high to low. Please see Figure 9.
Figure 9. Signal plot shows how propagation delay is defined
Pulse-width distortion (PWD) is the difference between
tPHL and tPLH and often determines the maximum data
rate capability of a transmission system. PWD can be
expressed in percent by dividing the PWD (in ns) by the
minimum pulse width (in ns) being transmitted. Typically,
PWD on the order of 20-30% of the minimum pulse
width is tolerable. The PWD specification for ACPL-x72L
is 6ns (15%) maximum across recommended operating
conditions.
7
5
6
8
2
3
4
1
GND2
C1
C2
NC
VDD2
NC
VO
VDD1
VI
72
L
YYL
C1, C2 = 0.01 F TO 0.1 F
GND1
VDD2
C1
C2
VO
GND2
VDD1
VI
GND1
C1, C2 = 0.01 F TO 0.1 F
72
L
YYL
INPUT
tPLH
tPHL
OUTPUT
VI
VO
10%
90%
10%
VOH
VOL
0 V
50%
5 V CMOS
2.5 V CMOS
相關PDF資料 |
PDF描述 |
|---|---|
| ACPL-J313-300 | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| ACPL-K342-000E | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| ACPL-P454-500 | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| ACR7HYA58CFREQ | TCXO, CLOCK, 0.5 MHz - 160 MHz, ACMOS OUTPUT |
| ACS7HXCB7CFREQ | TCXO, CLOCK, 0.5 MHz - 160 MHz, ACMOS OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ACPL-072L-560 | 功能描述:高速光耦合器 3.3V/5V 25MBd RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| ACPL-072L-560E | 功能描述:高速光耦合器 3.3V/5V 25MBd RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| ACPL-074L | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:Single-channel and Dual-channel High Speed 15 MBd CMOS optocoupler with Glitch-Free Power-Up Feature |
| ACPL-074L-000E | 功能描述:高速光耦合器 Digital Optocouplers RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| ACPL-074L-060E | 功能描述:高速光耦合器 Digital Optocouplers RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。