參數資料
型號: ACPL-H312-060E
元件分類: 光電耦合器
英文描述: 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER
封裝: ROHS COMPLIANT, PLASTIC, SOP-6
文件頁數: 17/17頁
文件大小: 210K
代理商: ACPL-H312-060E
9
Table 7. Package Characteristics
Over recommended temperature (TA = -40 to 100°C) unless otherwise specified. All typicals at TA = 25°C.
Parameter
Symbol
Part Number Min.
Typ.
Max.
Units
Test Conditions
Fig.
Note
Input-Output Momentary
Withstand Voltage**
VISO
ACPL-H312
3750
Vrms
RH < 50%, t = 1 min.,
TA = 25°C
14, 16
ACPL-K312
5000
15, 16
Resistance
(Input-Output)
RI-O
1012
:
VI-O = 500 V
16
Capacitance
(Input-Output)
CI-O
0.6
pF
Freq= 1MHz
** The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refers to your equipment level safety specification or Avago Application Note 1074 entitled
“Optocoupler Input-Output Endurance Voltage.”
Notes:
1. Derate linearly above 70° C free-air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 μs.
3. Derate linearly above 78° C free-air temperature at a rate of 5.7 mW/°C.
4. Derate linearly above 78° C free-air temperature at a rate of 6.0 mW/°C. The maximum LED junction temperature should not exceed 125°C.
5. Maximum pulse width = 50 μs
6. In this test VOH is measured with a dc load current. When driving capacitive loads VOH will approach VCC as IOH approaches zero amps.
7. Maximum pulse width = 1 ms
8. This load condition approximates the gate load of a 1200 V/100A IGBT.
9. Pulse Width Distortion (PWD) is defined as |tPHL - tPLH| for any given device.
10. The difference between tPHL and tPLH between any two ACPL-H312/K312 parts under the same test condition.
11. Pins 3 and 4 need to be connected to LED common.
12. Common mode transient immunity in the high state is the maximum tolerable dVCM/dt of the common mode pulse, VCM, to assure that the output
will remain in the high state (i.e., VO > 15.0 V).
13. Common mode transient immunity in a low state is the maximum tolerable dVCM/dt of the common mode pulse, VCM, to assure that the output
will remain in a low state (i.e., VO < 1.0 V).
14. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage detection
current limit, II-O ≤ 5 μA).
15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 Vrms for 1 second (leakage detection
current limit II-O < 5 A).
16. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
相關PDF資料
PDF描述
ACPL-K63L-000E 2 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 15 Mbps
ACPL-K63L-560E 2 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 15 Mbps
ACPL-M72T-500E 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER
ACPL-M72T-060E 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER
ACPL-P611-060E 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 10 Mbps
相關代理商/技術參數
參數描述
ACPL-H312-500E 功能描述:邏輯輸出光電耦合器 2.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
ACPL-H312-560E 功能描述:邏輯輸出光電耦合器 2.5A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
ACPL-H342 制造商:Avago Technologies 功能描述:PLASTIC OPTOCOUPLER - Tape and Reel
ACPL-H342-000E 功能描述:邏輯輸出光電耦合器 Optocoupler RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
ACPL-H342-060E 功能描述:邏輯輸出光電耦合器 Optocoupler RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube