- 您現在的位置：買賣IC網 > PDF目錄294843 > ACPL-K63L-560E 2 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 15 Mbps PDF資料下載
參數資料
| 型號： | ACPL-K63L-560E |
| 元件分類： | 光電耦合器 |
| 英文描述： | 2 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 15 Mbps |
| 封裝： | ROHS COMPLIANT, SOP-8 |
| 文件頁數： | 2/13頁 |
| 文件大?。?/td> | 172K |
| 代理商： | ACPL-K63L-560E |
10
Package Characteristics
All Typicals at TA = 25C.
Parameter
Sym.
Package
Min.
Typ.
Max
Units
Test Conditions
Fig.
Note
Input-Output
II-O*
Single
1
μA
45% RH, t = 5 s,
13, 14
Insulation
VI-O = 3 kV DC, TA = 25C
Input-Output
VISO
Single,
5000
V rms
RH ≤ 50%, t = 1 min,
13, 14
Momentary
Dual Channel
TA = 25C
Withstand
Voltage*
Input-Output
RI-O
Single,
1012
Ω
VI-O =500 V dc
1, 13, 15
Resistance
Dual Channel
Input-Output
CI-O
Single,
0.5
pF
f = 1 MHz, TA = 25C
1, 13, 15
Capacitance
Dual Channel
Input-Input
II-I
Dual Channel
0.005
μA
RH ≤ 45%, t = 5 s,
16
Insulation
VI-I = 500 V
Leakage
Current
Resistance
RI-I
Dual Channel
1011
Ω
16
(Input-Input)
Capacitance
CI-I
Dual Channel
0.25
pG
f = 1 MHz
16
(Input-Input)
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous volt-
age rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment
level safety specication or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
1.
Each channel.
2
Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed
20 mA.
3.
Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed
15 mA.
4.
Derate linearly above +80C free-air temperature at a rate of 2.7 mW/C.
5.
Bypassing of the power supply line is required, with a 0.1 μF ceramic disc capacitor adjacent to each optocoupler as illustrated in Figure 11.
Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm.
6.
The tPLH propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge
of the output pulse.
7.
The tPHL propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge
of the output pulse.
8.
tPSK is equal to the worst case dierence in tPHL and/or tPLH that will be seen between units at any given temperature and specied test con-
ditions.
9.
See test circuit for measurement details.
10. CMH is the maximum tolerable rate of rise on the common mode voltage to assure that the output will remain in a high logic state
(i.e., Vo > 2.0 V).
11. CML is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state
(i.e., Vo < 0.8 V).
12. For sinusoidal voltages, (|dVCM | / dt)max = πfCMVCM (p-p).
13. Single channel device is considered a two-terminal part when pins 1, 2, 3 are shorted together, and pins 4, 5, 6 shorted together separately.
Dual channel device is considered a two-terminal part when pins 1, 2, 3, 4 are shorted together, and pins 5, 6, 7, 8 are shorted together
separately.
14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for one second (leakage
detection current limit, II-O ≤ 5 μA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
15. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. For dual channel products only.
16. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. For dual channel products only.
相關PDF資料 |
PDF描述 |
|---|---|
| ACPL-M72T-500E | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| ACPL-M72T-060E | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| ACPL-P611-060E | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 10 Mbps |
| ACPM-7381-BLKR | 1920 MHz - 1980 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7381-OR1 | 1920 MHz - 1980 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ACPL-K64L | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:Ultra Low Power 10 MBd Digital CMOS Optocouplers |
| ACPL-K64L-000E | 功能描述:高速光耦合器 10MBd Optocoupler RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| ACPL-K64L-060E | 功能描述:高速光耦合器 10MBd Optocoupler RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| ACPL-K64L-500E | 功能描述:高速光耦合器 10MBd Optocoupler RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| ACPL-K64L-560E | 功能描述:高速光耦合器 10MBd Optocoupler RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。