參數資料
型號： AD13465BZ
廠商： ANALOG DEVICES INC
元件分類： ADC
英文描述： Dual Channel, 14-Bit, 65 MSPS A/D Converter with Analog Input Signal Conditioning
中文描述： DUAL 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
封裝： CERAMIC, LCC-68
文件頁數： 11/20頁
文件大小： 1433K
代理商： AD13465BZ
REV. 0
AD13465
–11–
Power Supplies
Care should be taken when selecting a power source. Linear
supplies are strongly recommended. Switching supplies tend to
have radiated components that may be
received
by the AD13465.
Each of the power supply pins should be decoupled as closely to
the package as possible, using 0.1
μ
F chip capacitors.
The AD13465 has separate digital and analog power supply pins.
The analog supplies are denoted AV
CC
and the digital supply
pins are denoted DV
CC
. AV
CC
and DV
CC
should be separate
power supplies. This is because the fast digital output swings
can couple switching current back into the analog supplies.
Note that AV
CC
must be held within +5% and
–
3% of 5 V. The
AD13465 is specified for DV
CC
= 3.3 V as this is a common
supply for digital ASICs.
Output Loading
Care must be taken when designing the data receivers for the
AD13465. The digital outputs drive an internal series resistor
(e.g., 100
) followed by a gate like 75LCX574. To minimize
capacitive loading, there should be only one gate on each output
pin. An example of this is shown in the evaluation board sche-
matic shown in Figure 10. The digital outputs of the AD13465
have a constant output slew rate of 1 V/ns. A typical CMOS
gate combined with a PCB trace will have a load of approximately
10 pF. Therefore, as each bit switches, 10 mA (10
pF
×
1
V
÷
1
ns
)
of dynamic current per bit will flow in or out of the device. A full-
scale transition can cause up to 140 mA (14 bits
×
10 mA/bit)
of transient current through the output stages. These switch-
ing currents are confined between ground and the DV
CC
pin.
Standard TTL gates should be avoided since they can apprecia-
bly add to the dynamic switching currents of the AD13465. It
should also be noted that extra capacitive loading will increase
output timing and invalidate timing specifications. Digital out-
put timing is guaranteed with 10 pF loads.
Figure 9. Evaluation Board Mechanical Layout
LAYOUT INFORMATION
The schematic of the evaluation board (Figure 10) represents a
typical implementation of the AD13465. The pinout of the
AD13465 is very straightforward and facilitates ease of use and
the implementation of high frequency/high resolution design
practices. It is recommended that high quality ceramic chip
capacitors be used to decouple each supply pin to ground directly
at the device. All capacitors can be standard high quality ceramic
chip capacitors.
Care should be taken when placing the digital output runs.
Because the digital outputs have such a high slew rate, the
capacitive loading on the digital outputs should be minimized.
Circuit traces for the digital outputs should be kept short and
connect directly to the receiving gate. Internal circuitry buffers
the outputs of the ADC through a resistor network to eliminate
the need to externally isolate the device from the receiving gate.
EVALUATION BOARD
The AD13465 evaluation board (Figure 9) is designed to
provide optimal performance for evaluation of the AD13465
analog-to-digital converter. The board encompasses everything
needed to ensure the highest level of performance for evaluating
the AD13465. The board requires an analog input signal, encode
clock, and power supply inputs. The clock is buffered on-board
to provide clocks for the latches. The digital outputs and out
clocks are available at the standard 40-pin connectors J1 and J2.
Power to the analog supply pins is connected via banana jacks.
The analog supply powers the associated components and
the analog section of the AD13465. The digital outputs of the
AD13465 are powered via banana jacks with 3.3 V. Contact the
factory if additional layout or applications assistance is required.
相關PDF資料
PDF描述
AD1362 ECONOLINE: RD & RC - Dual Output from a Single Input Rail- 1kVDC & 2kVDC Isolation- Power Sharing on Output- Custom Solutions Available- UL94V-0 Package Material- Efficiency to 86%
AD1362KD 16-Channel,12-Bit Data Acquisition System
AD1362SD 16-Channel,12-Bit Data Acquisition System
AD1376JD Complete, High Speed 16-Bit A/D Converter
AD1377JD Pressure Transducer, Series 19 mm, Compensated, Pressure Range: 0 psi to 10 psi, Gage, 1/8-27 NPT, 10 Vdc excitation
相關代理商/技術參數
參數描述
AD1348HB-F51 制造商:ADDA USA Corporation 功能描述:AXIAL FAN 127MM 48VDC 161.172CFM 53D 制造商:ADDA USA Corporation 功能描述:AXIAL FAN, 127MM, 48VDC, 161.172CFM, 53D 制造商:ADDA USA Corporation 功能描述:AXIAL FAN, 127MM, 48VDC, 161.172CFM, 53DBA, Frame Dimensions:127mm x 127mm x 38mm, Supply Voltage:48VDC, Current Rating:210mA, Flow Rate - Imperial:161.172cu.ft/min, Flow Rate - Metric:4.561m /min, Noise Rating:53dBA, Series:AD12738 , RoHS Compliant: Yes 制造商:ADDA USA Corporation 功能描述:DC-Fan, 127x127x38 mm, 48 Volts, 161 CFM, Ball Bearing, Lead Wire
AD1348HB-F53 制造商:ADDA USA Corporation 功能描述:48 VDC 161CFM BALL DC FAN WITH 3-11" LEADS, 127 X 127 X 38 M
AD1348LB-F51 制造商:ADDA Corporation 功能描述:AXIAL FAN 127MM 48VDC 107.49CFM 41DB 制造商:ADDA Corporation 功能描述:AXIAL FAN, 127MM, 48VDC, 107.49CFM, 41DB 制造商:ADDA Corporation 功能描述:AXIAL FAN, 127MM, 48VDC, 107.49CFM, 41DBA; Frame Dimensions:127mm x 127mm x 38mm; Supply Voltage:48VDC; Current Rating:110mA; Flow Rate - Imperial:107.49cu.ft/min; Flow Rate - Metric:3.041m /min; Noise Rating:41dBA; Bearing Type:Ball;RoHS Compliant: Yes
AD1348MB-F51 制造商:ADDA USA Corporation 功能描述:AXIAL FAN 127MM 48VDC 133.658CFM 47.5 制造商:ADDA USA Corporation 功能描述:AXIAL FAN, 127MM 48VDC, 133.658CFM, 47.5 制造商:ADDA USA Corporation 功能描述:AXIAL FAN, 127MM 48VDC, 133.658CFM, 47.5DBA, Frame Dimensions:127mm x 127mm x 38mm, Supply Voltage:48VDC, Current Rating:150mA, Flow Rate - Imperial:133.658cu.ft/min, Flow Rate - Metric:3.782m /min, Noise Rating:47.5dBA , RoHS Compliant: Yes 制造商:ADDA USA Corporation 功能描述:DC-Fan, 127x127x38 mm, 48 Volts, 133 CFM, Ball Bearing, Lead Wire
AD1348UB-F51 制造商:ADDA USA Corporation 功能描述:AXIAL FAN 127MM 48VDC 193.373CFM 56D 制造商:ADDA USA Corporation 功能描述:AXIAL FAN, 127MM, 48VDC, 193.373CFM, 56D 制造商:ADDA USA Corporation 功能描述:AXIAL FAN, 127MM, 48VDC, 193.373CFM, 56DBA, Frame Dimensions:127mm x 127mm x 38mm, Supply Voltage:48VDC, Current Rating:310mA, Flow Rate - Imperial:193.373cu.ft/min, Flow Rate - Metric:5.472m /min, Noise Rating:56dBA, Series:AD12738 , RoHS Compliant: Yes 制造商:ADDA USA Corporation 功能描述:DC-Fan, 127x127x38 mm, 48 Volts, 193 CFM, Ball Bearing, Lead Wire
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*