- 您現在的位置：買賣IC網 > PDF目錄1888 > AD1933WBSTZ-RL (Analog Devices Inc)IC DAC 24BIT SRL/SPI 64LQFP PDF資料下載
參數資料
| 型號： | AD1933WBSTZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/28頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 24BIT SRL/SPI 64LQFP |
| 標準包裝： | 1,500 |
| 位數： | 24 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 8 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 429mW |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 8 電壓，雙極 |
| 采樣率（每秒）： | * |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Data Sheet
AD1933
Rev. E | Page 13 of 28
POWER SUPPLY AND VOLTAGE REFERENCE
The AD1933 is designed for 3.3 V supplies. Separate power
supply pins are provided for the analog and digital sections.
These pins should be bypassed with 100 nF ceramic chip
capacitors, as close to the pins as possible, to minimize noise
pickup. A bulk aluminum electrolytic capacitor of at least 22 μF
should also be provided on the same PCB as the DAC. For
critical applications, improved performance is obtained with
separate supplies for the analog and digital sections. If this is
not possible, it is recommended that the analog and digital
supplies be isolated by means of a ferrite bead in series with
each supply. It is important that the analog supply be as clean
as possible.
The AD1933 includes a 3.3 V regulator driver that only requires
an external pass transistor and bypass capacitors to make a 5 V
to 3.3 V regulator. If the regulator driver is not used, connect
VSUPPLY, VDRIVE, and VSENSE to DGND.
All digital inputs are compatible with TTL and CMOS levels.
All outputs are driven from the 3.3 V DVDD supply and are
compatible with TTL and 3.3 V CMOS levels.
The DAC internal voltage reference (VREF) is brought out on
FILTR and should be bypassed as close as possible to the chip,
with a parallel combination of 10 μF and 100 nF. Any external
current drawn should be limited to less than 50 μA.
The internal reference can be disabled in the PLL and Clock
Control 1 register and FILTR can be driven from an external
source. This can be used to scale the DAC output to the clipping
level of a power amplifier based on its power supply voltage,
DAC output gain is proportional to the FILTR voltage.
The CM pin is the internal common-mode reference. It should
be bypassed as close as possible to the chip, with a parallel
combination of 47 μF and 100 nF. This voltage can be used to
bias external op amps to the common-mode voltage of the input
and output signal pins. The output current should be limited to
less than 0.5 mA source and 2 mA sink.
SERIAL DATA PORTS—DATA FORMAT
The eight DAC channels use a common serial bit clock (DBCLK)
and a common left-right framing clock (DLRCLK) in the serial
data port. The clock signals are all synchronous with the sample
rate. The normal stereo serial modes are shown in Figure 15.
The DAC serial data modes default to I2S. The ports can also be
programmed for left-justified, right-justified, and TDM modes.
The word width is 24 bits by default and can be programmed
for 16 or 20 bits. The DAC serial formats are programmable
according to the DAC Control 0 register. The polarity of the
DBCLK and DLRCLK is programmable according to the DAC
Control 1 register. The auxiliary TDM port is also provided for
applications requiring more than eight DAC channels. In this
mode, the AUXTDMLRCLK and AUXTDMBCLK pins are
configured as TDM port clocks. In regular TDM mode, the
DLRCLK and DBCLK pins are used as the TDM port clocks.
The auxiliary TDM serial port format and its serial clock
polarity are programmable according to the Auxiliary TDM
Port Control 0 register and the Auxiliary TDM Port Control 1
register. Both DAC and auxiliary TDM serial ports are
programmable to become the bus masters according to the
DAC Control 1 register and auxiliary TDM Control 1 register.
By default, both auxiliary TDM and DAC serial ports are in
slave mode.
TIME-DIVISION MULTIPLEXED (TDM) MODES
The AD1933 serial ports have several different TDM serial data
modes. The most commonly used configuration is shown in
Figure 10. In Figure 10, the eight on-chip DAC data slots are
packed into one TDM stream. In this mode, DBCLK is 256 fS.
The I/O pins of the serial ports are defined according to the
serial mode selected. For a detailed description of the function
of each pin in TDM and auxiliary modes, see Table 11.
The AD1933 allows systems with more than eight DAC channels
to be easily configured by the use of an auxiliary serial data port.
The DAC TDM-AUX mode is shown in Figure 11. In this mode,
the AUX channels are the last four slots of the 16-channel TDM
data stream. These slots are extracted and output to the AUX
serial port. One major difference between the TDM mode and
an auxiliary TDM mode is the assignment of the TDM port
pins, as shown in Table 11. In auxiliary TDM mode, DBCLK
and DLRCLK are assigned as the auxiliary port clocks, and
AUXTDMBCLK and AUXTDMLRCLK are assigned as the
TDM port clocks. In regular TDM or 16-channel, daisy-chain
TDM mode, the DLRCLK and DBCLK pins are set as the TDM
port clocks.
It should be noted that due to the high AUXTDMBCLK
frequency, 16-channel auxiliary TDM mode is available only
in the 48 kHz/44.1 kHz/32 kHz sample rate.
SLOT 1
LEFT 1
SLOT 2
RIGHT 1
SLOT 3
LEFT 2
SLOT 4
RIGHT 2
MSB
MSB–1
MSB–2
DATA
BCLK
LRCLK
SLOT 5
LEFT 3
SLOT 6
RIGHT 3
SLOT 7
LEFT 4
SLOT 8
RIGHT 4
LRCLK
BCLK
DATA
256 BCLKs
32 BCLK
06624
-010
Figure 10. DAC TDM (8-Channel I2S Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| AD1934WBSTZ-RL | IC DAC 8CH W/ON-CHIP PLL 48LQFP |
| AD1937WBSTZ | IC CODEC 4/ADC DIFF OUT 64-LQFP |
| AD1938WBSTZ | IC CODEC 24BIT 4ADC/8DAC 48LQFP |
| AD1939WBSTZ-RL | AUDIO CODEC W/ON CHIP 4ADC 8DAC |
| AD1953YSTZ | IC DSP DAC AUDIO3CH/26BIT 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD1933YSTZ | 功能描述:IC DAC 24BIT SRL/SPI 8CH RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD1933YSTZ-RL | 功能描述:IC DAC 24BIT SRL/SPI 8CH RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD1934 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel DAC with PLL, 192 kHz, 24 Bits |
| AD1934WBSTZ | 功能描述:IC DAC 8CH W/ON-CHIP PLL 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD1934WBSTZ-RL | 功能描述:IC DAC 8CH W/ON-CHIP PLL 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。