- 您現在的位置：買賣IC網 > PDF目錄373864 > AD22050R (ANALOG DEVICES INC) Single-Supply Sensor Interface Amplifier PDF資料下載
參數資料
| 型號： | AD22050R |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Single-Supply Sensor Interface Amplifier |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封裝： | PLASTIC, SOIC-8 |
| 文件頁數： | 8/8頁 |
| 文件大小： | 148K |
| 代理商： | AD22050R |
AD22050
–8–
REV. C
A unique method of feedback around A1, provided by R9 and
R7, sets the closed-loop gain of the preamplifier to
×
10 (from
the input pins). The feedback network is balanced by the inclu-
sion of R6 and R8. The small value of R7 results in a more
practical value for R9 (which would have to be 2 M
if the
feedback were taken directly to the inputs of A1). R8 is not
directly connected to ground, but to an optional voltage of one
half that is applied to Pin 7 (OFS). It is trimmed to within
close tolerances through R10 and R11. This allows the output
of A1 to be offset to midscale, typically +V
S
/2, by tying Pins 6
and 7 together. (For an example of the use of this feature, see
Figure 12.) The gain is adjusted by the single resistor R5,
which acts only on the differential signal. More importantly, it
also results in much less feed forward of the common-mode
signal to the output of A1, which, being a single-supply circuit,
has no means of pulling this output down toward ground in
those circumstances where the common-mode input is very
positive while the net differential signal is small. (The output of
A1 is the collector of a PNP transistor whose emitter is tied to
+V
S
.) R16 is specifically included to alleviate this problem.
The output of the preamplifier is connected to Pin 3 via R12, a
100 k
resistor that is trimmed to within
±
3%. The inclusion
of R12 allows a low-pass filter to be formed, with an accurate
time constant, by placing a capacitor from Pin 3 to ground. By
separating the connections at Pins 3 and 4, a two-pole Sallen
and Key filter can be formed (see Low-Pass Filtering section)
and also provides a means for setting the overall gain to values
other than
×
20 (see
Altering the Gain section).
The output buffer has a gain of
×
2, set by the feedback network
around op amp A2, formed by R15 and R13
i
R14. Note that this
gain is not trimmed to a precise value, but may have a tolerance
of
±
3% (max). Only the overall gain of A1 and A2 is trimmed to
within
±
0.5% by R5. As a consequence, the gain of A1 may be
in error by
±
3% (max) as the trim to R5 absorbs the initial error
in the gain of A2. In most applications Pins 3 and 4 are simply
tied together, but the output buffer can be used independently if
desired. The offset voltage of A2 is nulled during manufacture.
R17 is included to minimize the offset due to bias currents. It is
recommended, in applications where A2 is used independently
and the source resistance is less than 100 k
, that the necessary
extra resistance should be included.
The output of A2 is the collector of a PNP transistor whose
emitter is tied to +V
S
. The bias current out of the inverting
input of this amplifier generates an offset voltage of about +1 mV
in R13
i
R14, which is passed directly to the output via R15. This
sets the lowest output that can be reached when there is no load
resistor. However, the output can drive a 1 k
load to at least
+4.5 V when +V
S
= +5 V. If operation to much lower minimum
voltages is essential, a load resistor can be added externally.
P
AD22050
A1
A2
+V
S
R12
100k
V
A2
C1
5pF
R1
200k
V
R18
1k
V
A1
R19 1k
V
C2
5pF
R4
41k
V
R9
10k
V
R7
250
V
R17
95k
V
R15
10k
V
OUT
R16
10k
V
R14
20k
V
R13
20k
V
R5
2.6k
V
R3
41k
V
GND
OFS
R6
250k
V
R8
9k
V
R2
200k
V
R11
2k
V
R10
2k
V
IN+
IN–
Figure 16. Simplified Schematic of AD22050, Including Component Values
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Plastic SOIC Package
(SO-8)
0.1968 (5.00)
0.1890 (4.80)
8
5
4
1
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.1574 (4.00)
0.1497 (3.80)
0.0688 (1.75)
0.0532 (1.35)
SEATING
PLANE
0.0098 (0.25)
0.0040 (0.10)
0.0192 (0.49)
0.0138 (0.35)
0.0500
(1.27)
BSC
0.0098 (0.25)
0.0075 (0.19)
0.0500 (1.27)
0.0160 (0.41)
8
8
0
8
0.0196 (0.50)
0.0099 (0.25)
3
45
8
Plastic Mini-DIP Package
(N-8)
8
1
4
5
0.430 (10.92)
0.348 (8.84)
0.280 (7.11)
0.240 (6.10)
PIN 1
SEATING
PLANE
0.022 (0.558)
0.014 (0.356)
0.060 (1.52)
0.015 (0.38)
0.210 (5.33)
MAX
0.130
(3.30)
MIN
0.070 (1.77)
0.045 (1.15)
0.100
(2.54)
BSC
0.160 (4.06)
0.115 (2.93)
0.325 (8.25)
0.300 (7.62)
0.015 (0.381)
0.008 (0.204)
0.195 (4.95)
0.115 (2.93)
C
相關PDF資料 |
PDF描述 |
|---|---|
| AD22055 | ECONOLINE: RD & RC - Dual Output from a Single Input Rail- 1kVDC & 2kVDC Isolation- Power Sharing on Output- Custom Solutions Available- UL94V-0 Package Material- Efficiency to 86% |
| AD22055N | Single Supply Bridge Transducer Amplifier |
| AD22055R | Single Supply Bridge Transducer Amplifier |
| AD22057 | Single-Supply Sensor Interface Amplifier |
| AD22057N | RD Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 12V; Output Voltage (Vdc): 12V; Power: 2W; Low Cost 2W Dual Output Converter; Industry Standard SIP7 and DIP14 Packages; Power Sharing on Outputs; Optional Continuous Short Circuit Protected; 1kVDC & 2kVDC Isolation Options; UL94V-0 Package Material; Efficiency to 86% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD22050R-REEL | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single 36V 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:IC SENSOR IC - Tape and Reel |
| AD22050R-REEL7 | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single 36V 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:IC SENSOR IC - Tape and Reel |
| AD22050RZ | 功能描述:IC AMP DIFF SINGLE SUPPLY 8-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD22050RZ-REEL | 功能描述:IC AMP DIFF SINGLE SUPPLY 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD22050RZ-REEL7 | 功能描述:IC AMP DIFF SINGLE SUPPLY 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。