- 您現在的位置：買賣IC網 > PDF目錄11609 > AD2S80ABD (Analog Devices Inc)IC R/D CONV TRACKING 40CDIP PDF資料下載
參數資料
| 型號： | AD2S80ABD |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC R/D CONV TRACKING 40CDIP |
| 標準包裝： | 1 |
| 類型： | R/D 轉換器 |
| 輸入類型： | 并聯 |
| 輸出類型： | 數字 |
| 接口： | 并聯 |
| 電流 - 電源： | 30mA |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 40-CDIP（0.600"，15.24mm） |
| 供應商設備封裝： | 40-DIP |
| 包裝： | 管件 |
AD2S80A
REV. B
–13–
VELOCITY ERRORS
The signal at the INTEGRATOR OUTPUT pin relative to the
ANALOG GROUND pin is an analog voltage proportional to
the rate of change of the input angle. This signal can be used to
stabilize servo loops or in the place of a velocity transducer.
Although the conversion loop of the AD2S80A includes a digital
section there is an additional analog feedback loop around the
velocity signal. This ensures against flicker in the digital posi-
tional output in both dynamic and static states.
A better quality velocity signal will be achieved if the following
points are considered:
1. Protection.
The velocity signal should be buffered before use.
2. Reversion error.
The reversion error can be nulled by varying one supply rail
relative to the other.
3. Ripple and Noise.
Noise on the input signals to the converter is the major cause of
noise on the velocity signal. This can be reduced to a minimum
if the following precautions are taken:
The resolver is connected to the converter using separate
twisted pair cable for the sine, cosine and reference signals.
Care is taken to reduce the external noise wherever possible.
An HF filter is fltted before the Phase Sensitive Demodulator
(as described in the section HF FILTER).
A resolver is chosen that has low residual voltage, i.e., a small
signal in quadrature with the reference.
Components are selected to operate the AD2S80A with the
lowest acceptable bandwidth.
Feedthrough of the reference frequency should be removed by
a filter on the velocity signal.
Maintenance of the input signal voltages at 2 V rms will
prevent LSB flicker at the positional output. The analog
feedback or hysteresis employed around the VCO and the
intergrator is a function of the input signal levels (see sec-
tion “INTEGRATOR”) .
Following the preceding precautions will allow the user to use
the velocity signal in very noisy environments, for example,
PWM motor drive applications. Resolver/converter error curves
may exhibit apparent acceleration/deceleration at a constant
velocity. This results in ripple on the velocity signal of frequency
twice the input rotation.
1Reversion error, or side-to-side nonlinearity, is a result of differences in the
up and down rates of the VCO.
SOURCES OF ERRORS
Integrator Offset
Additional inaccuracies in the conversion of the resolver signals
will result from an offset at the input to the integrator as it will
be treated as an error signal. This error will typically be 1 arc
minute over the operating temperature range.
A description of how to adjust from zero offset is given in the
section “COMPONENT SELECTION” and the circuit required
is shown in Figure 1.
Differential Phase Shift
Phase shift between the sine and cosine signals from the resolver
is known as differential phase shift and can cause static error.
Some differential phase shift will be present on all resolvers as a
result of coupling. A small resolver residual voltage (quadrature
voltage) indicates a small differential phase shift. Additional phase
shift can be introduced if the sine channel wires and the cosine
channel wires are treated differently. For instance, different cable
lengths or different loads could cause differential phase shift.
The additional error caused by differential phase shift on the
input signals approximates to
Error = 0.53 a
× b arc minutes
where a = differential phase shift (degrees).
b = signal to reference phase shift (degrees).
This error can be minimized by choosing a resolver with a small
residual voltage, ensuring that the sine and cosine signals are
handled identically and removing the reference phase shift (see
section “CONNECTING THE RESOLVER”). By taking these
precautions the extra error can be made insignificant.
Under static operating conditions phase shift between the refer-
ence and the signal lines alone will not theoretically affect the
converter’s static accuracy.
However, most resolvers exhibit a phase shift between the signal
and the reference. This phase shift will give rise under dynamic
conditions to an additional error defined by:
Shaft Speed (rps)
× Phase Shift (Degrees )
Reference Frequency
For example, for a phase shift of 20 degrees, a shaft rotation of
22 rps and a reference frequency of 5 kHz, the converter will
exhibit an additional error of:
22
× 20
5000
0.088 Degrees
This effect can be eliminated by placing a phase shift in the
reference to the converter equivalent to the phase shift in the
resolver (see section “CONNECTING THE RESOLVER”).
Note: Capacitive and inductive crosstalk in the signal and reference
leads and wiring can cause similar problems.
C
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/20KJ24PN | CONN RCPT 24POS WALL MNT W/PINS |
| D38999/24WG75SA | CONN RCPT 4POS JAM NUT W/SCKT |
| D38999/26FG75SA | CONN PLUG 4POS STRAIGHT W/SCKT |
| D38999/26MG11SA | CONN PLUG 11POS STRAIGHT W/SCKT |
| V24A36C400BG3 | CONVERTER MOD DC/DC 36V 400W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S80AJD | 功能描述:IC R/D CONV TRACKING 40CDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S80AKD | 功能描述:IC R/D CONV TRACKING 40CDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S80ALD | 功能描述:IC R/D CONV TRACKING 40CDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S80ASD | 功能描述:IC R/D CONV TRACKING 40CDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S80ASD/883B | 功能描述:數據轉換 IC - 多種 40 PIN DIP 8 ARC MIN 883B RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。