DD
參數資料
型號: AD2S99AP
廠商: Analog Devices Inc
文件頁數: 4/8頁
文件大小: 0K
描述: IC OSC SINUSOIDAL 20KHZ 20-PLCC
標準包裝: 49
類型: 振蕩器 - 正弦
頻率: 2kHz ~ 20kHz
電源電壓: ±4.75 V ~ 5.25 V
電流 - 電源: 8mA
工作溫度: -40°C ~ 85°C
封裝/外殼: 20-LCC(J 形引線)
包裝: 管件
供應商設備封裝: 20-PLCC(9x9)
安裝類型: 表面貼裝
AD2S99
REV. B
–4–
20
0
6
2
4
0
12
8
10
14
16
18
28
24
20
16
12
8
ADDITIONAL RESISTANCE – k
RESISTOR PULLUP TO V
DD FROM FBIAS
FREQUENCY
kHz
Figure 2. Typical Added Resistance Value
AD2S99 OSCILLATOR OUTPUT STAGE
The output of the AD2S99 oscillator consists of two sinusoidal
signals, EXC, and EXC. EXC is 180
° phase advanced with re-
spect to EXC. The excitation winding of a transducer should be
connected across EXC (Pin 17) and EXC (Pin 18).
With low impedance transducers, it may be necessary to in-
crease the output current drive of the AD2S99. In such an in-
stance, an external buffer amplifier can be used to provide gain
(as needed), and additional current drive for the excitation out-
put (either EXC or EXC) of the AD2S99, providing a single
ended drive to the transducer. Refer to Figures 6, 7 and 8 for
sample buffer configurations.
The amplitude modulated SIN and COS output signals from a re-
solver should be connected as feedback signals to the AD2S99.
The SYNREF output compensates for any primary to secondary
phase errors in the resolver. These errors can degrade the accuracy
of a Resolver-to-Digital Converter (R/D Converter).
SIN, from the resolver, should be connected to the AD2S99 SIN
input and COS should be connected to the AD2S99 COS input.
The SIN Lo, COS Lo (resolver signal returns) should be con-
nected to AGND and the R/D Converter as applicable.
The synthesized reference (SYNREF) from the AD2S99 should
be connected to the reference input pin of the R/D Converter.
The SYNREF signal is a square wave at the oscillator frequency
of amplitude
±3 V p-p and is phase coherent with the SIN and
COS inputs. If this signal is used to drive the reference input of
the AD2S90 R/D Converter, a coupling capacitor and resistor to
GND must be connected between the SYNREF output of the
AD2S99 and the REF input of the R/D Converter (see Figure
3). Please read the appropriate R/D Converter data sheets for
further clarification.
LOSS OF SIGNAL
During normal operation when both the SIN and COS signals
on the resolver secondary windings are connected to the
AD2S99, the LOS output pin of the AD2S99 (Pin 11) is at a
Logic Lo (
<0.7 V). If both the SIN and COS signals on the re-
solver secondary windings fall below the LOS threshold level of
the AD2S99, the LOS pin of the AD2S99 will pull up to a
Logic Hi (VDD) level.
CONNECTING THE AD2S99 OSCILLATOR
Refer to Figure 1. Positive supply voltage VDD should be con-
nected to Pin 12 and negative supply voltage VSS should be con-
nected to both Pins 19 and 20. Reversal of these power supplies will
destroy the device. The appropriate voltage level for the power
supplies is
±5 V dc ± 5%. Both V
SS Pins (19 and 20) must be
connected together, and Digital Ground (Pin 6) must be con-
nected to Analog Ground (Pin 16) locally at the AD2S99.
V
DD
NC = NO CONNECT
NC
SIN
NC
DGND
COS
FBIAS
SEL1
V
SS
SEL2
V
SS
NC
SYNREF
NC
LOS
V
DD
EXC
NC
AGND
NC
19
3
1
2
20
4
5
8
6
7
12
13
911
10
18
17
14
16
15
AD2S99
EXC
0.1
F
V
SS
4.7
F
REF
RESOLVER
SIN
0.1
F
4.7
F
R
X*
TO AD2S80/
AD2S90 REF INPUT
50k
*R
X
IS ONLY REQUIRED FOR INTERMEDIATE FREQUENCIES.
FIXED FREQUENCIES ONLY REQUIRE A LINK.
SEL2 = GND ]
SEL1 = V
SS
]
–5kHz MODE
INCREASE R
X
TO LOWER
OUTPUT FREQUENCY
(SEE GRAPH)
COS
.
100nF
100k
Figure 1. Typical Configuration
It is recommended that decoupling capacitors are connected in
parallel between VDD and Analog Ground and VSS and Analog
Ground in close proximity to the AD2S99. The recommended
values for the decoupling capacitors are 100 nF (ceramic) and
4.7
F (tantalum). When multiple AD2S99s are used, separate
decoupling capacitors should be used for each AD2S99.
FREQUENCY ADJUSTMENT
The output frequency of the AD2S99 is programmable to four
standard frequencies (2, 5, 10, or 20 kHz) using the SEL1 and
SEL2 pins. The output can also be adjusted to provide interme-
diate frequencies by connecting a resistor from the FBIAS pin to
the positive supply VDD. The FBIAS pin is connected directly to
VDD during normal operation. A graph showing the typical
added resistance values for various intermediate frequencies is
provided in Figure 2. The procedure for obtaining an intermedi-
ate frequency is:
1. Set the output frequency via the SEL1, SEL2 pins to the fre-
quency immediately above the required intermediate frequency.
2. Connect the frequency adjust pin FBIAS to VDD via an exter-
nal resistor.
For example: to obtain an output frequency of 8 kHz, set the
nominal output frequency to 10 kHz by connecting SEL1 to
GND and SEL2 to VSS. Connect FBIAS to VDD via a 6 k
resistor (refer to Figure 2).
相關PDF資料
PDF描述
MAX196ACAI+T IC DAS 12BIT 6CH 28-SSOP
LTC6904MPMS8#PBF IC OSC SILICON 68MHZ 8MSOP
MAX197ACAI+T IC DAS 12BIT SNGL 28-SSOP
MAX198ACAI+T IC DAS 12BIT 6CH 28-SSOP
LTC6905MPS5#TRMPBF IC OSC SILICON 170MHZ TSOT23-5
相關代理商/技術參數
參數描述
AD2S99APZ 功能描述:IC OSC SINUSOIDAL 20KHZ 20-PLCC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 可編程計時器和振蕩器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:45 系列:- 類型:溫度 - 補償晶體振蕩器(TCXO) 計數:- 頻率:25MHz 電源電壓:3.135 V ~ 3.465 V 電流 - 電源:1.5mA 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 包裝:管件 供應商設備封裝:16-SOIC W 安裝類型:表面貼裝
AD2S99APZ 制造商:Analog Devices 功能描述:Phase Lock Loop (PLL) IC
AD2S99APZ-MOOG 制造商:Analog Devices 功能描述:
AD2S99BP 功能描述:IC OSC SINUSOIDAL 20KHZ 20-PLCC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 可編程計時器和振蕩器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:45 系列:- 類型:溫度 - 補償晶體振蕩器(TCXO) 計數:- 頻率:25MHz 電源電壓:3.135 V ~ 3.465 V 電流 - 電源:1.5mA 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 包裝:管件 供應商設備封裝:16-SOIC W 安裝類型:表面貼裝
AD2S99BPZ 功能描述:IC OSC SINUSOIDAL 20KHZ 20PLCC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 可編程計時器和振蕩器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:45 系列:- 類型:溫度 - 補償晶體振蕩器(TCXO) 計數:- 頻率:25MHz 電源電壓:3.135 V ~ 3.465 V 電流 - 電源:1.5mA 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 包裝:管件 供應商設備封裝:16-SOIC W 安裝類型:表面貼裝