- 您現在的位置：買賣IC網 > PDF目錄9375 > AD5232BRUZ50 (Analog Devices Inc)IC DGTL POT 256POS 50K 16TSSOP PDF資料下載
參數資料
| 型號： | AD5232BRUZ50 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/24頁 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 256POS 50K 16TSSOP |
| 標準包裝： | 96 |
| 接片： | 256 |
| 電阻（歐姆）： | 50k |
| 電路數： | 2 |
| 溫度系數： | 標準值 600 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 2.7 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 配用： | EVAL-AD5232-10EBZ-ND - BOARD EVALUATION FOR AD5232-10 |
Data Sheet
AD5232
Rev. C | Page 15 of 24
SERIAL DATA INTERFACE
The AD5232 contains a 4-wire SPI-compatible digital interface
(SDI, SDO, CS, and CLK) and uses a 16-bit serial data-word
that is loaded MSB first. The format of the SPI-compatible word
is shown in Table 7. The chip select (CS) pin must be held low
until the complete data-word is loaded into the SDI pin. When
CS returns high, the serial data-word is decoded according to
the instructions in Table 8. The command bits (Cx) control the
operation of the digital potentiometer. The address bits (Ax)
determine which register is activated. The data bits (Dx) are the
values that are loaded into the decoded register. Table 9 provides
an address map of the EEMEM locations. The last command
instruction executed prior to a period of no programming activity
should be the no operation (NOP) command instruction (Com-
mand Instruction 0). This instruction places the internal logic
circuitry in a minimum power dissipation state.
02618-
033
COUNTER
CLK
SDI
5V
SDO
GND
PR
WP
AD5232
CS
VALID
COMMAND
SERIAL
REGISTER
COMMAND
PROCESSOR
AND ADDRESS
DECODE
RPULL-UP
Figure 33. Equivalent Digital Input/Output Logic
The AD5232 has an internal counter that counts a multiple of
16 bits (per frame) for proper operation. For example, the AD5232
works with a 16-bit or 32-bit word, but it cannot work properly
with a 15-bit or 17-bit word. To prevent data from mislocking
(due to noise, for example), the counter resets if the count is not
a multiple of 4 when CS goes high, but the data remains in the
register if the count is a multiple of 4. In addition, the AD5232 has
a subtle feature whereby, if CS is pulsed without CLK and SDI,
the part repeats the previous command (except during power-
up). As a result, care must be taken to ensure that no excessive
noise exists in the CLK or CS line that may alter the effective
number of bits pattern.
The equivalent serial data input and output logic is shown in
Figure 33. The open-drain SDO is disabled whenever CS is logic
high. The SPI interface can be used in two slave modes: CPHA = 1,
CPOL = 1; and CPHA = 0, CPOL = 0. CPHA and CPOL refer
to the control bits that dictate SPI timing in the following micro-
processors and MicroConverter devices: the ADuC812 and the
ADuC824, the M68HC11, and the MC68HC16R1/916R1. ESD
protection of the digital inputs is shown in Figure 34 and Figure 35.
GND
02618-
034
INPUTS
300
VDD
LOGIC
PINS
AD5232
Figure 34. Equivalent ESD Digital Input Protection
GND
02618-
035
INPUTS
300
VDD
WP
AD5232
Figure 35. Equivalent WP Input Protection
DAISY-CHAINING OPERATION
The SDO pin serves two purposes: it can be used to read back
the contents of the wiper setting and the EEMEM using Command
Instruction 9 and Command Instruction 10 (see Table 8), or it can
be used for daisy-chaining multiple devices.The remaining com-
mand instructions are valid for daisy-chaining multiple devices in
simultaneous operations. Daisy chaining minimizes the number
of port pins required from the controlling IC (see Figure 36).
The SDO pin contains an open-drain N-channel FET that requires
a pull-up resistor if this function is used. As shown in Figure 36,
users must tie the SDO pin of one package to the SDI pin of the
next package. Users may need to increase the clock period because
the pull-up resistor and the capacitive loading at the SDO-to-SDI
interface may require additional time delay between subsequent
packages. If two AD5232s are daisy-chained, 32 bits of data are
required. The first 16 bits go to U2, and the second 16 bits with
the same format go to U1. The 16 bits are formatted to contain
the 4-bit instruction, followed by the 4-bit address, followed by
the eight bits of data. The CS pin should be kept low until all 32 bits
are locked into their respective serial registers. The CS pin is then
pulled high to complete the operation.
SDI
SDO
CLK
SDI
SDO
AD5232
U1
AD5232
U2
02618-
036
CS
VDD
MicroConverter
RP
2.2k
Figure 36. Daisy-Chain Configuration Using the SDO
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2NT-MX-B1 | CONVERTER MOD DC/DC 6.5V 75W |
| AD5231BRU10 | IC DGTL POT 1024POS 10K 16TSSOP |
| VE-B3H-MY-F1 | CONVERTER MOD DC/DC 52V 50W |
| AD5206BN50 | IC DGTL POT 256POS 50K 6CH 24DIP |
| ISL12028IVAZ | IC RTC/CALENDAR EEPROM 14-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5232BRUZ50-REEL7 | 功能描述:IC POT DGTL DUAL 256POS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5232EVAL10 | 制造商:Analog Devices 功能描述:Evaluation Board For Dual Non-Volatile Memory Digital Potentiometer 制造商:Analog Devices 功能描述:DUAL 8BITEEMEM EVAL BOARD - Bulk |
| AD5232EVAL100 | 制造商:Analog Devices 功能描述:DUAL 8BITEEMEM EVAL BOARD - Bulk |
| AD5232EVAL50 | 制造商:Analog Devices 功能描述:DUAL 8BITEEMEM EVAL BOARD - Bulk |
| AD5233 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Nonvolatile Memory Digital Potentiometers |
發布緊急采購，3分鐘左右您將得到回復。