- 您現在的位置：買賣IC網 > PDF目錄9306 > AD5271BRMZ-100-RL7 (Analog Devices Inc)DIGITAL POT 256POS 100K SINGLE PDF資料下載
參數資料
| 型號： | AD5271BRMZ-100-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | DIGITAL POT 256POS 100K SINGLE |
| 產品變化通告： | AD527(0,1) Pin Requirement 14/Dec/2010 |
| 標準包裝： | 1,000 |
| 接片： | 256 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 5 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線串行 |
| 電源電壓： | 2.7 V ~ 5.5 V，±2.5 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | Q5815854 |
AD5270/AD5271
Data Sheet
Rev. F | Page 20 of 24
SHUT-DOWN MODE
The AD5270/AD5271 can be shut down by executing the
software shutdown command, Command 9 (see Table 11), and
setting the LSB to 1. This feature places the RDAC in a zero-
power-consumption state where Terminal Ax is open circuited
and the Wiper Terminal Wx remains connected. It is possible to
execute any command from Table 11 while the AD5270/AD5271
are in shutdown mode. The parts can be taken out of shutdown
mode by executing Command 9 and setting the LSB to 0 or by a
software reset, Command 4 (see Table 11).
RESISTOR PERFORMANCE MODE
This mode activates a new, patented 1% end-to-end resistor
tolerance that ensures a ±1% resistor tolerance error on each
resistor tolerance. The resistor performance mode is activated by
programming Bit C2 of the control register.
RESET
The AD5270/AD5271 can be reset through software by executing
Command 4 (see Table 11). The reset command loads the
RDAC register with the contents of the most recently programmed
50-TP memory location. The RDAC register loads with
midscale if no 50-TP memory location has been previously
programmed.
Table 12. Write and Read to RDAC and 50-TP Memory
DIN
SDO1
Action
0x1C03
0xXXXX
Enable update of the wiper position and the 50-TP memory contents through the digital interface.
0x0500
0x1C03
Write 0x100 to the RDAC register; wiper moves to full-scale position.
0x0800
0x0500
Prepares data read from RDAC register.
0x0C00
0x100
Stores RDAC register content into the 50-TP memory. A 16-bit word appears out of SDO, where the last 10-bits contain
the contents of the RDAC register (0x100).
0x1800
0x0C00
Prepares data read of last programmed 50-TP memory monitor location.
0x0000
0xXX19
NOP Instruction 0 sends a 16-bit word out of SDO, where the six LSBs last six bits contain the binary address of the last
programmed 50-TP memory location, for example, 0x19 (see Table 13).
0x1419
0x0000
Prepares data read from Memory Location 0x19.
0x2000
0x0100
Prepares data read from the control register. Sends a 16-bit word out of SDO, where the last 10-bits contain the
contents of Memory Location 0x19.
0x0000
0xXXXX
NOP Instruction 0 sends a 16-bit word out of SDO, where the last four bits contain the contents of the control register.
If Bit C3 = 1, the fuse program command successful.
1
X is don’t care.
Table 13. Control Register Bit Map
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
0
C3
C2
C1
C0
Table 14. Control Register Bit Description
Bit Name
Description
C0
50-TP program enable
0 = 50-TP program disabled (default)
1 = enable device for 50-TP program
C1
RDAC register write protect
0 = wiper position frozen to value in 50-TP memory (default)1
1 = allow update of wiper position through digital interface
C2
R-performance enable
0 = RDAC resistor tolerance calibration enabled (default)
1 = RDAC resistor tolerance calibration disabled
C3
50-TP memory program success bit
0 = fuse program command unsuccessful (default)
1 = fuse program command successful
1
Wiper position frozen to the last value programmed in the 50-TP memory. The wiper is frozen to midscale if the 50-TP memory has not been previously programmed.
相關PDF資料 |
PDF描述 |
|---|---|
| SY89295UTG | IC DELAY LINE 1024TAP 32-TQFP |
| AD5271BRMZ-20-RL7 | IC DGTL POT SGL 256POS 10MSOP |
| VE-B4V-MY-F1 | CONVERTER MOD DC/DC 5.8V 50W |
| VE-B40-MY-F3 | CONVERTER MOD DC/DC 5V 50W |
| SY100EP195VTG | IC DELAY LINE 1024TAP 32-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5271BRMZ-20 | 功能描述:IC DGTL POT 20K 256POS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| AD5271BRMZ-20 | 制造商:Analog Devices 功能描述:Digital Potentiometer IC |
| AD5271BRMZ-20-RL7 | 功能描述:IC DGTL POT SGL 256POS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5272 | 制造商:AD 制造商全稱:Analog Devices 功能描述:1024-/256-Position, 1% Resistor Tolerance Error, I2C Interface and 50-TP Memory Digital Rheostat |
| AD5272BCPZ-100-RL7 | 功能描述:IC RHEOSTAT 5V 50-TP 1024 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。