- 您現在的位置：買賣IC網 > PDF目錄8572 > AD5390BCPZ-5-REEL (Analog Devices Inc)IC DAC 14BIT 16CHAN 5V 64LFCSP PDF資料下載
參數資料
| 型號： | AD5390BCPZ-5-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 27/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 14BIT 16CHAN 5V 64LFCSP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 產品變化通告： | AD5390/1/2 Redesign Change 16/May/2012 |
| 設計資源： | 8 to 16 Channels of Programmable Voltage with Excellent Temperature Drift Performance Using AD5390/1/2 (CN0029) AD5390/91/92 Channel Monitor Function (CN0030) |
| 標準包裝： | 2,500 |
| 設置時間： | 8µs |
| 位數： | 14 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 16 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 35mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 16 電壓，單極 |
| 采樣率（每秒）： | 125k |
| 配用： | EVAL-AD5390EBZ-ND - BOARD EVALUATION FOR AD5390 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Data Sheet
AD5390/AD5391/AD5392
Rev. E | Page 33 of 44
CONTROL REGISTER WRITE
Table 25 shows the control register contents for the AD5390 and the AD5392. Table 26 provides bit descriptions. Note that REG1 = REG0 = 0,
A3 to A0 = 1100, and DB13 to DB0 contain the control register data.
Table 25. AD5390/AD5392 Control Register Contents
MSB
LSB
CR13
CR12
CR11
CR10
CR9
CR8
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
Table 26. AD5390 and AD5392 Bit Descriptions
Bit
Description
CR13
Power-Down Status. This bit is used to configure the output amplifier state in power–down mode.
CR13 = 1: Amplifier output is high impedance (default on power-up).
CR13 = 0: Amplifier output is 100 kΩ to ground.
CR12
REF Select. This bit selects the operating internal reference for the AD539x. CR12 is programmed as follows:
CR12 = 1: Internal reference is 2.5 V (AD5390-2/AD5392-5 default). Recommended operating reference for AD539x-5.
CR12 = 0: Internal reference is 1.25 V (AD5390-3/AD5392-3 default). Recommended operating reference for AD5390-3 and
AD5392-3.
CR11
Current Boost Control. This bit is used to boost the current in the output amplifier, thus altering its slew rate and is
configured as follows:
CR11 = 1: Boost mode on. This maximizes the bias current in the output amplifier, optimizing its slew rate but increasing
the power dissipation.
CR11 = 0: Boost mode off (default on power-up). This reduces the bias current in the output amplifier and reduces the
overall power consumption.
CR10
Internal/External Reference. This bit determines if the DAC uses its internal reference or an external reference.
CR10 = 1: Internal reference enabled. Reference output depends on data loaded to CR12.
CR10 = 0: External reference selected (default on power-up).
CR9
Channel Monitor Enable (see Table 23).
CR9 = 1: Monitor enabled (default on power-up). This enables the channel monitor function. Following a write to the
monitor channel in the SFR register, the selected channel output is routed to the MON_OUT pin.
CR9 = 0: Monitor disabled. When monitor is disabled, the MON_OUT pin is three-stated.
CR8
Thermal Monitor Function. When enabled, this function is used to monitor the internal die temperature of the
AD5390/AD5392. The thermal monitor powers down the output amplifiers when the temperature exceeds 130°C. This
function can be used to protect the device when the power dissipation of the device may be exceeded, if a number of
output channels are simultaneously short circuited. A soft power-up re-enables the output amplifiers if the die
temperature has dropped below 130°C.
CR8 = 1: Thermal monitor enabled.
CR8 = 0: Thermal monitor disabled (default on power-up).
CR7 to CR4
Don’t Care.
CR3 to CR2
Toggle Function Enable. This function lets the user toggle the output between two codes loaded to the A and B register
for each DAC. Control Register Bits CR3 and CR2 are used to enable individual groups of eight channels for operation in
toggle mode on the AD5390 and AD5392, as follows:
CR3
Group 1
Channel 8 to Channel 15
CR2
Group 0
Channel 0 to Channel 7
CR2 is the only active bit on the AD5392. Logic 1 written to any bit enables a group of channels and Logic 0 disables a
group. LDAC is used to toggle between the two registers.
CR1 to CR0
Don’t Care.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5390BCPZ-3-REEL | IC DAC 14BIT 16CHAN 3V 64LFCSP |
| LTC1592ACG#TRPBF | IC D/A CONV 16BIT SOFTSPAN16SSOP |
| LTC1592ACG#TR | IC D/A CONV 16BIT SOFTSPAN16SSOP |
| AD7537KP | IC DAC 12BIT LC2MOS DUAL 28-PLCC |
| AD7543BQ | IC DAC 12BIT SRL INP MULT 16CDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5390BCPZ-5-REEL7 | 功能描述:IC DAC 14BIT 16CHAN 5V 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5390BST-3 | 制造商:Analog Devices 功能描述:DAC 16-CH Resistor-String 14-bit 52-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:16-CHN 3V SINGLE SUPPLY 14-BIT VOUT I.C. - Bulk 制造商:Analog Devices 功能描述:IC 14BIT DAC 16CH 3V 5390 LQFP52 |
| AD5390BST-3-REEL | 制造商:Analog Devices 功能描述:DAC 16-CH Resistor-String 14-bit 52-Pin LQFP T/R |
| AD5390BST-5 | 制造商:Analog Devices 功能描述:DAC 16-CH Resistor-String 14-bit 52-Pin LQFP 制造商:Analog Devices 功能描述:IC 14BIT DAC 16CH 5V 5390 LQFP52 |
| AD5390BST-5-REEL | 制造商:Analog Devices 功能描述:DAC 16-CH Resistor-String 14-bit 52-Pin LQFP T/R |
發布緊急采購，3分鐘左右您將得到回復。