- 您現在的位置：買賣IC網 > PDF目錄373881 > AD5516 (Analog Devices, Inc.) ECONOLINE: RO & RE - Industry Standard Pinout- 1kVDC & 2kVDC Isolation- UL94V-0 Package Material- Toroidal Magnetics- Fully Encapsulated- Custom Solutions Available- Efficiency to 85% PDF資料下載
參數資料
| 型號： | AD5516 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | ECONOLINE: RO & RE - Industry Standard Pinout- 1kVDC & 2kVDC Isolation- UL94V-0 Package Material- Toroidal Magnetics- Fully Encapsulated- Custom Solutions Available- Efficiency to 85% |
| 中文描述： | 16通道，12位電壓輸出DAC，具有14位增量模式 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 197K |
| 代理商： | AD5516 |
REV. 0
AD5516
–13–
APPLICATION CIRCUITS
The AD5516 is suited for use in many applications, such as level
setting, optical, industrial systems, and automatic test applica-
tions. In level setting and servo applications where a fine-tune
adjust is required, the Mode 2 function increases resolution.
The following figures show the AD5516 used in some potential
applications.
AD5516 in a Typical ATE System
The AD5516 is ideally suited for the level setting function in
automatic test equipment. A number of DACs are required to
control pin drivers, comparators, active loads, parametric mea-
surement units, and signal timing. Figure 10 shows the AD5516
in such a system.
DAC
STORED
DATA AND
INHIBIT
PATTERN
PERIOD
GENERATION
AND
DELAY
TIMING
DACs
FORMATTER
COMPARE
REGISTER
SYSTEM BUS
DAC
DAC
DAC
DAC
ACTIVE
LOAD
PARAMETRIC
MEASUREMENT
UNIT
SYSTEM BUS
DAC
DAC
COMPARATOR
DUT
DRIVER
Figure 10. AD5516 in an ATE System
AD5516 in an Optical Network Control Loop
The AD5516 can be used in optical network control applica-
tions that require a large number of DACs to perform a control
and measurement function. In the example shown below, the
outputs of the AD5516 are fed into amplifiers and used to control
actuators that determine the position of MEMS mirrors in an
optical switch. The exact position of each mirror is measured and
the readings are multiplexed into an 8-channel, 14-bit ADC
(AD7865). The increment and decrement modes of the DACs are
useful in this application as it allows the user 14-bit resolution.
The control loop is driven by an ADSP-2106x, a 32-bit
SHARC DSP.
AD5516
0
15
MEMS
MIRROR
ARRAY
0
15
S
E
N
S
O
R
S
ADG609
2
0
7
AD7865
AD8644
2
ADSP-2106x
Figure 11. AD5516 in an Optical Control Loop
POWER SUPPLY DECOUPLING
In any circuit where accuracy is important, careful consideration
of the power supply and ground return layout helps to ensure the
rated performance. The printed circuit board on which the AD5516
is mounted should be designed so that the analog and digital
sections are separated and confined to certain areas of the board. If
the AD5516 is in a system where multiple devices require an
AGND-to-DGND connection, the connection should be made at
one point only. The star ground point should be established as
close as possible to the device. For supplies with multiple pins
(AV
CC
1, AV
CC
2) it is recommended to tie those pins together. The
AD5516 should have ample supply bypassing of 10
μ
F in parallel
with 0.1
μ
F on each supply located as closely to the package as
possible, ideally right up against the device. The 10
μ
F capacitors
are the tantalum bead type. The 0.1
μ
F capacitor should have low
effective series resistance (ESR) and effective series inductance
(ESI), like the common ceramic types that provide a low-impedance
path to ground at high frequencies, to handle transient currents
due to internal logic switching.
The power supply lines of the AD5516 should use as large a trace
as possible to provide low-impedance paths and reduce the effects
of glitches on the power supply line. Fast switching signals such
as clocks should be shielded with digital ground to avoid radiating
noise to other parts of the board, and should never be run near
the reference inputs. A ground line routed between the D
IN
and
SCLK lines will help reduce crosstalk between them (not required
on a multilayer board as there will be a separate ground plane, but
separating the lines will help). It is essential to minimize noise
on REFIN.
Avoid crossover of digital and analog signals. Traces on opposite
sides of the board should run at right angles to each other. This
reduces the effects of feedthrough through the board. A micro-
strip technique is by far the best, but not always possible with a
double-sided board. In this technique, the component side of
the board is dedicated to ground plane while signal traces are
placed on the solder side.
As is the case for all thin packages, care must be taken to avoid
flexing the package and to avoid a point load on the surface of
the package during the assembly process.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5516-1 | 16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
| AD5516-2 | 16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
| AD5516-3 | 16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
| AD5516ABC-1 | 16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
| AD5516ABC-2 | 16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5516_03 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
| AD5516-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
| AD5516-2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
| AD5516-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 12-Bit Voltage-Output DAC with 14-Bit Increment Mode |
| AD5516ABC-1 | 功能描述:IC DAC 12BIT 16CH 74-CSPBGA RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。