- 您現在的位置：買賣IC網 > PDF目錄1979 > AD5532BBCZ-1 (Analog Devices Inc)IC DAC 14BIT 32CH BIPO 74-CSPBGA PDF資料下載
參數資料
| 型號： | AD5532BBCZ-1 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/16頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 32CH BIPO 74-CSPBGA |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1 |
| 設置時間： | 22µs |
| 位數： | 14 |
| 數據接口： | 串行 |
| 轉換器數目： | 34 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 623mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 74-LBGA，CSPBGA |
| 供應商設備封裝： | 74-CSPBGA（12x12） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 32 電壓，單極 |
| 采樣率（每秒）： | 45k |
| 配用： | EVAL-AD5532HSEBZ-ND - BOARD EVAL FOR AD5532HS EVAL-AD5532EBZ-ND - BOARD EVAL FOR AD5532 |
REV. A
AD5532B
–15–
APPLICATION CIRCUITS
AD5532B in a Typical ATE System
The AD5532B is ideally suited for use in automatic test
equipment. Several DACs are required to control pin drivers,
comparators, active loads, and signal timing. Traditionally,
sample-and-hold devices were used in these applications.
The AD5532B has several advantages: no refreshing is required,
there is no droop, pedestal error is eliminated, and there is no
need for extra filtering to remove glitches. Overall a higher level
of integration is achieved in a smaller area (see Figure 15).
DACs
ACTIVE
LOAD
DRIVER
COMPARATOR
FORMATTER
COMPARE
REGISTER
STORED
DATA
AND INHIBIT
PATTERN
PERIOD
GENERATION
AND
DELAY
TIMING
SYSTEM BUS
DAC
PARAMETRIC
MEASUREMENT
UNIT
SYSTEM BUS
DUT
DAC
Figure 15. AD5532B in an ATE System
Typical Application Circuit (DAC Mode)
The AD5532B can be used in many optical networking applications
that require a large number of DACs to perform control and
measurement functions. In the example shown in Figure 16, the
outputs of the AD5532B are amplified and used to control actuators
that determine the position of MEMS mirrors in an optical switch.
The exact position of each mirror is measured using sensors. The
sensor readings are muxed using four dual 4-channel matrix switches
(ADG739) and fed back to an 8-channel 14-bit ADC (AD7856).
The control loop is driven by an ADSP-2191M, a 16-bit fixed-
point DSP with three SPORT interfaces and two SPI ports. The
DSP uses some of these serial ports to write data to the DAC,
control the multiplexer, and read back data from the ADC.
ADSP-2191M
AD5532B
MEMS
MIRROR
ARRAY
ADG739
4
AD7856
1
32
S
E
N
S
O
R
AD8544
2
1
32
1
8
Figure 16. Typical Optical Control and
Measurement Application Circuit
Typical Application Circuit (ISHA Mode)
The AD5532B can be used to set up voltage levels on 32 channels
as shown in the circuit below. An AD780 provides the 3 V refer-
ence for the AD5532B, and for the AD5541 16-bit DAC. A simple
3-wire serial interface is used to write to the AD5541. Because
the AD5541 has an output resistance of 6.25 kW (typ), the time
taken to charge/discharge the capacitance at the VIN pin is signifi-
cant. Thus an AD820 is used to buffer the DAC output. Note
that it is important to minimize noise on VIN and REFIN when
laying out this circuit.
AD5532B*
OFFS_IN
OFFS_OUT
REFIN
VIN
SCLK
DIN
SYNC
AVCC DVCC VSS
VDD
VOUT 0–31
AD820
CS
DIN
SCLK
*ADDITIONAL PINS OMITTED FOR CLARITY
AD780*
VOUT
AD5541*
REF
AVCC
Figure 17. Typical Application Circuit (ISHA Mode)
POWER SUPPLY DECOUPLING
In any circuit where accuracy is important, careful consideration
of the power supply and ground return layout helps to ensure the
rated performance. The printed circuit board on which the
AD5532B is mounted should be designed so that the analog and
digital sections are separated, and confined to certain areas of the
board. If the AD5532B is in a system where multiple devices require
an AGND-to-DGND connection, the connection should be made
at one point only. The star ground point should be established
as close as possible to the device. For supplies with multiple pins
(VSS, VDD, AVCC), it is recommended to tie those pins together.
The AD5532B should have ample supply bypassing of 10
F in
parallel with 0.1
F on each supply located as close to the package
as possible, ideally right up against the device. The 10
F capacitors
are the tantalum bead type. The 0.1
F capacitor should have
low effective series resistance (ESR) and effective series induc-
tance (ESI), like the common ceramic types that provide a low
impedance path to ground at high frequencies, to handle transient
currents due to internal logic switching.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5541ABRMZ | IC DAC 16BIT 2.7-5.5V 10-MSOP |
| AD5542ABRUZ | IC DAC 16BIT SRL 16TSSOP |
| AD5542CR | IC DAC 16BIT SERIAL-IN 14-SOIC |
| AD5543BR | IC DAC 16BIT SRLIN/CUR OUT 8SOIC |
| AD5543SRMZ-EP | IC DAC 16BIT SRL 8MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5532HS | 制造商:AD 制造商全稱:Analog Devices 功能描述:32-Channel 14-Bit DAC with High-Speed 3-Wire Serial Interface |
| AD5532HSABC | 功能描述:IC DAC 14BIT 32CH 74-CSPBGA RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5532HSABCZ | 功能描述:IC DAC 14BIT 32CH HS 74-CSPBGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5533 | 制造商:AD 制造商全稱:Analog Devices 功能描述:32-Channel Infinite Sample-and-Hold |
| AD5533ABC-1 | 制造商:Analog Devices 功能描述:Sample and Hold 32-CH 16us 74-Pin CSP-BGA |
發布緊急采購，3分鐘左右您將得到回復。