- 您現在的位置：買賣IC網 > PDF目錄8592 > AD5669RBCPZ-1500R7 (Analog Devices Inc)IC DAC 16BIT I2C/SRL 16LFCSP-WQ PDF資料下載
參數資料
| 型號： | AD5669RBCPZ-1500R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT I2C/SRL 16LFCSP-WQ |
| 標準包裝： | 1 |
| 系列： | denseDAC |
| 設置時間： | 2.5µs |
| 位數： | 16 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 8 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 16-LFCSP-WQ（4x4） |
| 包裝： | 標準包裝 |
| 輸出數目和類型： | * |
| 采樣率（每秒）： | 166k |
| 其它名稱： | AD5669RBCPZ-1500R7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD5629R/AD5669R
Rev. D | Page 27 of 32
LDAC FUNCTION
The outputs of all DACs can be updated simultaneously using
the hardware LDAC pin.
Synchronous LDAC
The DAC registers are updated after new data is read in. LDAC
can be permanently low or pulsed as in Figure 2.
Asynchronous LDAC
The outputs are not updated at the same time that the input
registers are written to. When LDAC goes low, the DAC
registers are updated with the contents of the input register.
Alternatively, the outputs of all DACs can be updated simulta-
neously using the software LDAC function by writing to Input
Register n and updating all DAC registers. Command 0011 is
reserved for this software LDAC function.
An LDAC register gives the user extra flexibility and control
over the hardware LDAC pin. Setting the LDAC bit register
to 0 for a DAC channel means that this channel’s update is
controlled by the LDAC pin. If this bit is set to 1, this channel
updates synchronously; that is, the DAC register is updated
after new data is read, regardless of the state of the LDAC pin.
It effectively sees the LDAC pin as being tied low. See Table 16
for the LDAC register mode of operation.
This flexibility is useful in applications where the user wants
to simultaneously update select channels while the rest of the
channels are synchronously updating. Writing to the DAC
using command 0110 loads the 8-bit LDAC register (DB7 to
DB0). The default for each channel is 0, that is, the LDAC pin
works normally. Setting the bits to 1 means the DAC channel
is updated regardless of the state of the LDAC pin. See Table 17
for the contents of the input shift register during the load LDAC
register mode of operation.
POWER SUPPLY BYPASSING AND GROUNDING
When accuracy is important in a circuit, it is helpful to carefully
consider the power supply and ground return layout on the board.
should have separate analog and digital sections. If the AD5629R/
AD5669R are in a system where other devices require an
AGND-to-DGND connection, the connection should be made
at one point only. This ground point should be as close as
possible to the AD5629R/AD5669R.
The power supply to the AD5629R/AD5669R should be
bypassed with 10 F and 0.1 F capacitors. The capacitors
should be as physically close as possible to the device, with the
0.1 F capacitor ideally right up against the device. The 10 F
capacitors are the tantalum bead type. It is important that the
0.1 F capacitor have low effective series resistance (ESR) and
low effective series inductance (ESI), such as is typical of
common ceramic types of capacitors. This 0.1 F capacitor
provides a low impedance path to ground for high frequencies
caused by transient currents due to internal logic switching.
The power supply line should have as large a trace as possible to
provide a low impedance path and reduce glitch effects on the
supply line. Clocks and other fast switching digital signals should
be shielded from other parts of the board by digital ground. Avoid
crossover of digital and analog signals if possible. When traces
cross on opposite sides of the board, ensure that they run at right
angles to each other to reduce feedthrough effects through the
board. The best board layout technique is the microstrip technique,
where the component side of the board is dedicated to the ground
plane only and the signal traces are placed on the solder side.
However, this is not always possible with a 2-layer board.
Table 16.
EE
AA
Register
LDAC
Load DAC Register
A
LDACE
A
Bits (DB7 to DB0)
A
LDACE
A
Pin
A
LDACE
A
Operation
0
1/0
Determined by
A
LDACE
A
pin.
1
X—don’t care
DAC channels update, overriding the
A
LDACE
A
pin. DAC channels see
A
LDACE
A
as 0.
Table 17. 32-Bit Input Shift Register Contents for
AA
LDACEE
AA
Register Function
MSB
LSB
DB23
DB22
DB21
DB20
DB19
DB18
DB17
DB16
DB15
to DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
0
1
0
X
DAC H
DAC G
DAC F
DAC E
DAC D
DAC C
DAC B
DAC A
Command bits (C3 to C0)
Address bits (A3 to A0)—
don’t cares
Don’t
cares
Setting
A
LDACE
A
bit to 1 overrides
A
LDACE
A
pin
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1597-1BCG#TR | IC DAC 16BIT PAR 28SSOP |
| VI-23J-MY-B1 | CONVERTER MOD DC/DC 36V 50W |
| LTC2600IGN | IC DAC R-R 16-BIT OCTAL 16-SSOP |
| LTC1596CCSW#PBF | IC D/A CONV 16BIT MLTPLYNG16SOIC |
| AD5557CRU | IC DAC 14BIT 2CH I OUT 38TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5669RBCPZ-1-RL7 | 功能描述:IC DAC 16BIT I2C/SRL 16LFCSP-WQ RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:denseDAC 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5669RBCPZ-2500R7 | 功能描述:IC DAC 16BIT I2C/SRL 16LFCSP-WQ RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:denseDAC 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5669RBCPZ-2-RL7 | 功能描述:IC DAC 16BIT I2C/SRL 16LFCSP-WQ RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:denseDAC 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5669RBRUZ-2 | 功能描述:IC DAC 16BIT I2C/SRL 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:denseDAC 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5669RBRUZ-2-RL7 | 功能描述:IC DAC 16BIT I2C/SRL 16TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:denseDAC 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
發布緊急采購，3分鐘左右您將得到回復。