- 您現在的位置：買賣IC網 > PDF目錄8610 > AD5734RBREZ-REEL7 (Analog Devices Inc)IC DAC 14BIT DSP/SRL 24TSSOP PDF資料下載
參數資料
| 型號： | AD5734RBREZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 14BIT DSP/SRL 24TSSOP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 設計資源： | Software Configurable 14-Bit Quad-Channel Unipolar/Bipolar Voltage Output Using AD5734R (CN0084) |
| 標準包裝： | 1,000 |
| 設置時間： | 10µs |
| 位數： | 14 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 4 |
| 電壓電源： | 雙 ± |
| 功率耗散（最大）： | 310mW |
| 工作溫度： | -40°C ~ 80°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm）裸露焊盤 |
| 供應商設備封裝： | 24-TSSOP 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 4 電壓，單極；4 電壓，雙極 |
| 采樣率（每秒）： | 100k |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD5724R/AD5734R/AD5754R
Rev. E | Page 30 of 32
DESIGN FEATURES
ANALOG OUTPUT CONTROL
In many industrial process control applications, it is vital that
the output voltage be controlled during power-up. When the
supply voltages change during power-up, the VOUTx pins are
clamped to 0 V via a low impedance path (approximately 4 kΩ).
To prevent the output amplifiers from being shorted to 0 V
during this time, Transmission Gate G1 is also opened (see
Figure 48). These conditions are maintained until the power
supplies have stabilized and a valid word is written to a DAC
register. At this time, G2 opens and G1 closes.
VOUTA
G1
G2
VOLTAGE
MONITOR
AND
CONTROL
0
64
65
-0
10
Figure 48. Analog Output Control Circuitry
POWER-DOWN MODE
Each DAC channel of the AD5724R/AD5734R/AD5754R can
be individually powered down. By default, all channels are in
power-down mode. The power status is controlled by the power
channel is in power-down mode its output pin is clamped to
ground through a resistance of approximately 4 kΩ and the
output of the amplifier is disconnected from the output pin.
OVERCURRENT PROTECTION
Each DAC channel of the AD5724R/AD5734R/AD5754R
incorporates individual overcurrent protection. The user has
two options for the configuration of the overcurrent protection:
constant current clamp or automatic channel power-down. The
configuration of the overcurrent protection is selected via the
clamp enable bit in the control register.
Constant Current Clamp (Clamp Enable = 1)
If a short circuit occurs in this configuration, the current is
clamped at 20 mA. This event is signaled to the user by the
setting of the appropriate overcurrent (OCX) bit in the power
control register. Upon removal of the short-circuit fault, the
OCX bit is cleared.
Automatic Channel Power-Down (Clamp Enable = 0)
If a short circuit occurs in this configuration, the shorted
channel powers down and its output is clamped to ground via
a resistance of approximately 4 kΩ. Also, at this time, the output
of the amplifier is disconnected from the output pin. The short-
circuit event is signaled to the user via the overcurrent bits (OCX),
while the power-up bits (PUX) indicate which channels have
powered down. After the fault is rectified, the channels can be
powered up again by setting the PUX bits.
THERMAL SHUTDOWN
The AD5724R/AD5734R/AD5754R incorporate a thermal
shutdown feature that automatically shuts down the device if
the core temperature exceeds approximately 150°C. The thermal
shutdown feature is disabled by default and can be enabled
via the TSD enable bit of the control register. In the event of a
thermal shutdown, the TSD bit of the power control register is set.
INTERNAL REFERENCE
The on-chip voltage reference is powered down by default. If
an external voltage reference source is to be used, the internal
reference must remain powered down at all times. If the internal
reference is to be used as the reference source, it must be powered
up via the PUREF bit of the power control register. The internal
reference voltage is accessible at the REFIN/REFOUT pin for use
as a reference source for other devices within the system. If the
internal reference is to be used external to the AD5724R/
AD5734R/AD5754R, it must first be buffered.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8138ARM-REEL7 | IC AMP DIFF LDIST LP 95MA 8MSOP |
| AD8138AR-REEL7 | IC AMP DIFF LDIST LP 95MA 8SOIC |
| LTC2610IUFD#TRPBF | IC DAC OCTAL R-R 14BIT 20-QFN |
| AD8310ARMZ-REEL7 | IC AMP LOGARITHMIC 8MSOP |
| VE-24P-IV-F1 | CONVERTER MOD DC/DC 13.8V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5735 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad Channel, 16-Bit, Serial Input, 4-20mA & Voltage Output DAC, Dynamic Power Control |
| AD5735_12 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad-Channel, 12-Bit, Serial Input, 4 mA to 20 mA |
| AD5735ACPZ | 功能描述:IC DAC QUAD VOLT CUR 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD5735ACPZ-REEL7 | 功能描述:IC DAC QUAD VOLT CUR 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5737 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad Channel, 16-Bit, Serial Input, 4-20mA Output DAC, Dynamic Power Control, HART Connectivity |
發布緊急采購，3分鐘左右您將得到回復。