參數資料
型號： AD5780ACPZ
廠商： Analog Devices Inc
文件頁數： 11/28頁
文件大?。?/td> 0K
描述： IC DAC VOLT OUT 18BIT 24LFCSP
標準包裝： 1
設置時間： 2.5µs
位數： 18
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
電壓電源： 模擬和數字，雙 ±
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 24-VFQFN 裸露焊盤，CSP
供應商設備封裝： 24-LFCSP-VQ EP（4x5）
包裝： 托盤
輸出數目和類型： 1 電壓，雙極
配用： EVAL-AD5780SDZ-ND - BOARD EVALUATION FOR AD5780
Data Sheet
AD5780
Rev. E | Page 19 of 28
Standalone Operation
The serial interface works with both a continuous and noncon-
tinuous serial clock. A continuous SCLK source can be used
only if SYNC is held low for the correct number of clock cycles.
In gated clock mode, a burst clock containing the exact number
of clock cycles must be used, and SYNC must be taken high after
the final clock to latch the data. The first falling edge of SYNC
starts the write cycle. Exactly 24 falling clock edges must be
applied to SCLK before SYNC is brought high again. If SYNC is
brought high before the 24th falling SCLK edge, the data written
is invalid. If more than 24 falling SCLK edges are applied before
SYNC is brought high, the input data is also invalid.
The input shift register is updated on the rising edge of SYNC.
For another serial transfer to take place, SYNC must be brought
low again. After the end of the serial data transfer, data is
automatically transferred from the input shift register to the
addressed register. When the write cycle is complete, the output
can be updated by taking LDAC low while SYNC is high.
Readback
The contents of all the on-chip registers can be read back via
the SDO pin. Table 7 outlines how the registers are decoded.
After a register has been addressed for a read, the next 24 clock
cycles clock the data out on the SDO pin. The clocks must be
applied while SYNC is low. When SYNC is returned high, the
SDO pin is placed in tristate. For a read of a single register, the
NOP function can be used to clock out the data. Alternatively,
if more than one register is to be read, the data of the first
register to be addressed can be clocked out at the same time
that the second register to be read is being addressed. The SDO
pin must be enabled to complete a readback operation. The
SDO pin is enabled by default.
HARDWARE CONTROL PINS
Load DAC Function (LDAC)
After data has been transferred into the input register of the
DAC, there are two ways to update the DAC register and DAC
output. Depending on the status of both SYNC and LDAC, one
of two update modes is selected: synchronous DAC update or
asynchronous DAC update.
Synchronous DAC Update
In this mode, LDAC is held low while data is being clocked into
the input shift register. The DAC output is updated on the rising
edge of SYNC.
Asynchronous DAC Update
In this mode, LDAC is held high while data is being clocked
into the input shift register. The DAC output is asynchronously
updated by taking LDAC low after SYNC has been taken high.
The update now occurs on the falling edge of LDAC.
Reset Function (RESET)
The AD5780 can be reset to its power-on state by two means:
either by asserting the RESET pin or by using the reset function
in the software control register (see Table 13). If the RESET pin
is not used, hardwire it to IOVCC.
Asynchronous Clear Function (CLR)
The CLR pin is an active low clear that allows the output to be
cleared to a user defined value. The 18-bit clearcode value is
programmed to the clearcode register (see Table 12). It is
necessary to maintain CLR low for a minimum amount of time
to complete the operation (see Figure 2). When the CLR signal
is returned high, the output remains at the clear value (if LDAC
is high) until a new value is loaded to the DAC register. The
output cannot be updated with a new value while the CLR pin is
low. A clear operation can also be performed by setting the CLR
bit in the software control register (see Table 13).
ON-CHIP REGISTERS
DAC Register
Table 9 outlines how data is written to and read from the DAC
register.
The following equation describes the ideal transfer function of
the DAC:
(
)
REFN
REFP
OUT
V
D
V
+
×
=
18
2
where:
VREFN is the negative voltage applied at the VREFN input pin.
VREFP is the positive voltage applied at the VREFP input pin.
D is the 18-bit code programmed to the DAC.
相關PDF資料
PDF描述
VE-BW2-MV-F3 CONVERTER MOD DC/DC 15V 150W
AD5544BRSZ IC DAC 16BIT SER QUAD 28SSOP
VE-BWV-MY-F1 CONVERTER MOD DC/DC 5.8V 50W
AD7228ACNZ IC DAC 8BIT OCTAL W/AMP 24DIP
MS27468T15B5PLC CONN HSG RCPT 5POS JAMNUT PINS
相關代理商/技術參數
參數描述
AD5780ACPZ-REEL7 功能描述:數模轉換器- DAC 18-Bit +/-1 LSB INL VOut RoHS:否 制造商:Analog Devices 轉換器數量:4 DAC 輸出端數量:4 轉換速率: 分辨率:12 bit 接口類型:Serial (I2C) 穩定時間: 最大工作溫度:+ 105 C 安裝風格: 封裝 / 箱體:TSSOP 封裝:Reel
AD5780BCPZ 功能描述:IC DAC VOLT OUT 18BIT 24LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND
AD5780BCPZ-REEL7 制造商:Analog Devices 功能描述:DAC 1-CH Segment 18-bit 24-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:18BIT, 1LSB, BUFFERED REF - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC VOLT OUT 18BIT 24LFCSP 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 18bit 1LSB buffered Ref 制造商:Analog Devices 功能描述:CONVERTER - DAC
AD5781 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra Stable, 16-Bit ±0.5 LSB INL
AD5781ARUZ 功能描述:IC DAC 18BIT SRL 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*