參數資料
型號: AD605AR-REEL7
廠商: Analog Devices Inc
文件頁數: 8/25頁
文件大?。?/td> 0K
描述: IC AMP VGA DUAL LN 40MA 16SOIC
標準包裝: 750
系列: X-AMP®
放大器類型: 可變增益
電路數: 2
轉換速率: 170 V/µs
-3db帶寬: 40MHz
電流 - 輸入偏壓: 400nA
電流 - 電源: 18mA
電流 - 輸出 / 通道: 40mA
電壓 - 電源,單路/雙路(±): 4.5 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 16-SOIC
包裝: 帶卷 (TR)
配用: AD605-EVALZ-ND - BOARD EVALUATION FOR AD605
AD605
Rev. F | Page 15 of 24
35
30
25
20
15
10
5
0
–5
–10
–15
–20
G
A
IN
(
d
B
)
40dB/V
30dB/V
20dB/V
LINEAR-IN-dB RANGE
OF AD605
1.0
0.5
1.5
2.0
2.5
3.0
GAIN CONTROL VOLTAGE
0
05
41
-03
8
Figure 37. Ideal Gain Curves vs. VREF
Usable gain control voltage ranges are 0.1 V to 2.9 V for the
20 dB/V scale and 0.1 V to 1.45 V for the 40 dB/V scale. VGN
voltages of less than 0.1 V are not used for gain control because
below 50 mV the channel is powered down. This can be used to
conserve power and at the same time gate-off the signal. The
supply current for a powered-down channel is 1.9 mA, and the
response time to power the device on or off is less than 1 μs.
FIXED GAIN AMPLIFIER AND INTERPOLATOR
CIRCUITS—APPLYING AN ACTIVE FEEDBACK
AMPLIFIER
A typical X-amp architecture is powered by a dual polarity
power supply. Because the AD605 operates from a single supply, a
supply common equal to half the value of the supply voltage is
required. An active feedback amplifier (AFA) is used to provide
a differential input and to implement the feedback loop. The
AFA in the AD605 is an op amp with two gm stages; one is used
in the feedback path, and the other is used as a highly linear
differential input.
A multisection distributed gm stage senses the voltages on the
ladder network, one stage for each of the ladder nodes. Only a
few of the stages are active at any time and are dependent on the
gain control voltage.
The AFA makes a differential input structure possible because
one of its inputs (G1) is fully differential; this input is made
up of a distributed gm stage. The second input (G2) is used for
feedback. The output of G1 is some function of the voltages
sensed on the attenuator taps that is applied to a high gain
amplifier (A0). Because of negative feedback, the differential
input to the high gain amplifier is zero; this in turn implies that
the differential input voltage to G2 times gm2 (the transconductance
of G2) is equal to the differential input voltage to G1 times gm1
(the transconductance of G1). Therefore, the overall gain
function of the AFA is
R2
R1
g
V
m
ATTEN
OUT
×
=
2
1
(7)
where:
VOUT is the output voltage.
VATTEN is the effective voltage sensed on the attenuator.
(
R1 + R2)/R2 = 42.
gm1/gm2 = 1.25; the overall gain is therefore 52.5 (34.4 dB).
The AFA has additional features that include the following:
inverting the output signal by switching the positive and negative
input to the ladder network; the possibility of using the IN
input as a second signal input; and independent control of the
DSX common-mode voltage. Under normal operating conditions,
it is best to connect a decoupling capacitor to Pin VOCM, in
which case, the common- mode voltage of the DSX is half of
the supply voltage; this allows for maximum signal swing.
Nevertheless, the common-mode voltage can be shifted up or
down by directly applying a voltage to VOCM. It can also be
used as another signal input, the only limitation being the
rather low slew rate of the VOCM buffer.
If the dc level of the output signal is not critical, another coupling
capacitor is normally used at the output of the DSX; again, this
is done for level shifting and to eliminate any dc offsets contributed
by the DSX (see the AC Coupling section).
The gain range of the DSX is programmable by a resistor connected
between Pin FBK and Pin OUT. The possible ranges are 14 dB to
+34.4 dB when the pins are shorted together or 0 dB to +48.4 dB
when FBK is left open. For the higher gain range, the bandwidth
of the amplifier is reduced by a factor of five to about 8 MHz
because the gain increased by 14 dB. This is the case for any
constant gain bandwidth product amplifier that includes the
active feedback amplifier.
相關PDF資料
PDF描述
TV04A780J-G TVS 400W 80V UNIDIRECT 5% SMA
TV02W600-G TVS 200W 60V UNIDIRECT SOD-123
TV02W5V0-HF TVS 200W 5V UNIDIRECT SOD-123
TV02W5V0-G TVS 200W 5V UNIDIRECT SOD-123
TV02W580-HF TVS 200W 58V UNIDIRECT SOD-123
相關代理商/技術參數
參數描述
AD605ARZ 功能描述:IC AMP VGA DUAL LN 40MA 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:X-AMP® 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
AD605ARZ-R7 功能描述:IC AMP VGA DUAL LN 40MA 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:X-AMP® 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件
AD605ARZ-RL 功能描述:IC AMP VGA DUAL LN 40MA 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:X-AMP® 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件
AD605ARZ-RL7 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, Low Noise, Single-Supply Variable Gain Amplifier
AD605B 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, Low Noise, Single-Supply Variable Gain Amplifier