- 您現在的位置：買賣IC網 > PDF目錄2135 > AD624SD (Analog Devices Inc)IC AMP INST 25MHZ PREC LN 16CDIP PDF資料下載
參數資料
| 型號： | AD624SD |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP INST 25MHZ PREC LN 16CDIP |
| 標準包裝： | 1 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 轉換速率： | 5 V/µs |
| 增益帶寬積： | 25MHz |
| -3db帶寬： | 1MHz |
| 電流 - 輸入偏壓： | 50nA |
| 電壓 - 輸入偏移： | 75µV |
| 電流 - 電源： | 3.5mA |
| 電壓 - 電源，單路/雙路(±)： | ±6 V ~ 18 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-CDIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-CDIP 側面銅焊 |
| 包裝： | 管件 |
REV. C
AD624
–9–
NOISE
The AD624 is designed to provide noise performance near the
theoretical noise floor. This is an extremely important design
criteria as the front end noise of an instrumentation amplifier is
the ultimate limitation on the resolution of the data acquisition
system it is being used in. There are two sources of noise in an
instrument amplifier, the input noise, predominantly generated
by the differential input stage, and the output noise, generated
by the output amplifier. Both of these components are present
at the input (and output) of the instrumentation amplifier. At
the input, the input noise will appear unaltered; the output
noise will be attenuated by the closed loop gain (at the output,
the output noise will be unaltered; the input noise will be ampli-
fied by the closed loop gain). Those two noise sources must be
root sum squared to determine the total noise level expected at
the input (or output).
The low frequency (0.1 Hz to 10 Hz) voltage noise due to the
output stage is 10
V p-p, the contribution of the input stage is
0.2
V p-p. At a gain of 10, the RTI voltage noise would be
1
V p-p,
10
G
2
+ 0.2
()2 . The RTO voltage noise would be
10.2
V p-p, 102 + 0.2 G
()
()2 . These calculations hold for
applications using either internal or external gain resistors.
INPUT BIAS CURRENTS
Input bias currents are those currents necessary to bias the input
transistors of a dc amplifier. Bias currents are an additional
source of input error and must be considered in a total error
budget. The bias currents when multiplied by the source resis-
tance imbalance appear as an additional offset voltage. (What is
of concern in calculating bias current errors is the change in bias
current with respect to signal voltage and temperature.) Input
offset current is the difference between the two input bias cur-
rents. The effect of offset current is an input offset voltage whose
magnitude is the offset current times the source resistance.
AD624
–VS
+VS
LOAD
TO
POWER
SUPPLY
GROUND
a. Transformer Coupled
AD624
–VS
+VS
LOAD
TO
POWER
SUPPLY
GROUND
b. Thermocouple
AD624
–VS
+VS
LOAD
TO
POWER
SUPPLY
GROUND
c. AC-Coupled
Figure 31. Indirect Ground Returns for Bias Currents
Although instrumentation amplifiers have differential inputs,
there must be a return path for the bias currents. If this is not
provided, those currents will charge stray capacitances, causing
the output to drift uncontrollably or to saturate. Therefore,
when amplifying “floating” input sources such as transformers
and thermocouples, as well as ac-coupled sources, there must
still be a dc path from each input to ground, (see Figure 31).
COMMON-MODE REJECTION
Common-mode rejection is a measure of the change in output
voltage when both inputs are changed by equal amounts. These
specifications are usually given for a full-range input voltage
change and a specified source imbalance. “Common-Mode
Rejection Ratio” (CMRR) is a ratio expression while “Common-
Mode Rejection” (CMR) is the logarithm of that ratio. For
example, a CMRR of 10,000 corresponds to a CMR of 80 dB.
In an instrumentation amplifier, ac common-mode rejection is
only as good as the differential phase shift. Degradation of ac
common-mode rejection is caused by unequal drops across
differing track resistances and a differential phase shift due to
varied stray capacitances or cable capacitances. In many appli-
cations shielded cables are used to minimize noise. This tech-
nique can create common-mode rejection errors unless the
shield is properly driven. Figures 32 and 33 shows active data
guards which are configured to improve ac common-mode
rejection by “bootstrapping” the capacitances of the input
cabling, thus minimizing differential phase shift.
AD624
RG2
–VS
REFERENCE
VOUT
–INPUT
+INPUT
+VS
G = 200
AD711
100
Figure 32. Shield Driver, G
≥ 100
AD624
RG1
–VS
REFERENCE
VOUT
–INPUT
+INPUT
+VS
–VS
AD712
100
RG2
Figure 33. Differential Shield Driver
相關PDF資料 |
PDF描述 |
|---|---|
| AD625SD | IC AMP INST 25MHZ LN 16CDIP |
| AD626AR | IC AMP DIFF LP 12MA 8SOIC |
| AD627BR | IC AMP INST R-R 25MA 8SOIC |
| AD628AR-REEL | IC AMP PGA DIFF PREC 8SOIC |
| AD629ARZ-RL | IC AMP DIFF 25MA LDRIFT 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD624SD/883B | 功能描述:儀表放大器 LOW NOISE PRECISION IN AM RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| AD625 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Programmable Gain Instrumentation Amplifier |
| AD62501P | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:7 SINGLE DRIVER |
| AD62550A | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:Class-D Audio Power Amplifier with USB / I2S Interface |
| AD62551A | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:USB controller with external Amplifier and Recording function |
發布緊急采購，3分鐘左右您將得到回復。